Subject	This is what I have done for the Z as well
Posted by	-Grimm- on February 10, 2020 at 1:15 PM
	This message has been viewed 331 times.
In Reply To	I did have a problem building oil pressure posted by Rocket man on February 09, 2020 at 06:01 PM
Message	Burn a FRAM oil filter (dont run those on your engine other than to prime, theyre useless). I used a hole saw to put a 1" PVC adapter (NPT to coupler) and a section of clear 1" nylon tubing hooked up to a vacuum. Turned the engine over by hand with the vacuum on until I could see oil in the clear tube. Dont forget to put a new oil filter on ------------------------------------------------------------------ 1992 300ZX NA 5 Sp KH6 (Gone) 1990 300ZX NA Auto 2+2 732 (Gone) 1991 300ZX TT 5 Sp TH1 (Gone) 1990 300ZX TT 5 Sp KH6 (Gone) 1990 300ZX TT 5 Sp 326 (GT600R E85) 2001 Honda Civic EX (DD) 2004 G35 Sport 6MT (DD) 2014 Nissan Murano (DD) 1969 Chevy C10 383/TH350 (Toy) 1969 Chevelle LS1/T56 (Toy)
Follow Ups	Starting rebuilt engine guidance - Kvert 19:38:03 02/07/20 From what I understand you disconnect the fuel system (n/m) - ctheobal 21:02:06 02/07/20 To prime oil - BlackholeZ 22:47:03 02/07/20 2nd - vorpalZed 09:28:41 02/08/20 And keep a wrench handy to clang on a jackstand. (n/m) - MixManMash 15:36:08 02/08/20 *rolls eyes... whistles* (n/m) - vorpalZed 22:16:03 02/08/20 lol thats so messed up... i swear I'd grab the nearest - nonstopna 18:51:02 02/09/20 If you're really that concerned, check out this prelube tank - Polishzx 23:17:45 02/07/20 Also the CAS position should be fine. Check if you have any - Polishzx 23:26:48 02/07/20 Yeah those are nice. - BlackholeZ 01:28:09 02/08/20 I've fired up many new longblocks.. - Stanky (BC) 11:02:26 02/08/20 I did the same, no issues. - platinumist 13:38:40 02/08/20 This. (n/m) - MixManMash 15:33:26 02/08/20 Agreed. I do the same. (n/m) - Woody75 (Denver) 12:50:17 02/10/20 i used Guapo's guide in the faq section. but - slayer fan 13:23:16 02/08/20 Assembly lube on bearing surfaces and cam shaft/lifters - ZXRider 20:08:56 02/08/20 Re: Assembly lube on bearing surfaces and cam shaft/lifters - nonstopna 19:02:48 02/09/20 I was told any assembly lube on the cylinder walls - ZXRider 20:22:40 02/09/20 ^Correct - -Grimm- 13:12:31 02/10/20 Interesting. Why ATF instead of engine oil? - ZXoltan 14:59:44 02/12/20 (From what I was told) ATF acts as a light lubricant for... - -Grimm- 13:06:56 02/13/20 I did have a problem building oil pressure - Rocket man 18:01:09 02/09/20 This is what I have done for the Z as well - -Grimm- 13:15:06 02/10/20 Re: Starting rebuilt engine guidance - Kvert 07:02:31 02/17/20 Re: Starting rebuilt engine guidance - Kvert 07:47:02 02/17/20
Post a Followup	You cannot reply to this message because you are not logged in.