Subject	Yeah if I ever have a house with a shop
Posted by	BlackholeZ on October 21, 2018 at 3:40 AM
	This message has been viewed 229 times.
In Reply To	What would be ideal is a front clip so you can check posted by MixManMash on October 19, 2018 at 04:25 PM
Message	or just cave ans lease out a shop, that's definitely happening. As is my plans involve building a keep out zone tool to be able to work on a stand. -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Splash shield for dual-POP setup? - GrecV2 19:42:10 10/11/18 Yes. (n/m) - Bernie (NoVA) 19:50:04 10/11/18 Hmm... Care to elaborate? Lol - GrecV2 19:56:24 10/11/18 Most folks use the shorter 350z/370z filters (n/m) - Bernie (NoVA) 20:37:20 10/11/18 Ahh. That makes sense. Thx. (n/m) - GrecV2 21:23:58 10/11/18 flower pot mod :-D (n/m) - ForceFedTT 23:40:50 10/11/18 flower pots for me as well, works great. (n/m) - BOOZT_JUNKIE 09:44:28 10/15/18 Proper solution is planar inlets that get them up out of the - BlackholeZ 21:43:48 10/11/18 This, combined with the 370Z filters. (n/m) - MixManMash 07:05:58 10/12/18 Like in my sig... - Barry (NJ) 10:11:20 10/12/18 Hmmm..."proper solution" is a bit strong... - ConVerTT 11:41:12 10/12/18 pic - planar intake support bracket - ConVerTT 11:56:25 10/12/18 Very nice setup! Looks like your elbows are shorter as well (n/m) - GrecV2 10:09:03 10/13/18 Thanks! I didn’t trim the elbows ... - ConVerTT 09:21:36 10/14/18 But, but I like 'em big and bouncy... (n/m) - MixManMash 12:28:59 10/12/18 LOL (n/m) - ConVerTT 14:03:15 10/12/18 Agreed (n/m) - Bernie (NoVA) 23:47:23 10/12/18 Proper from an airflow perspective - BlackholeZ 11:42:58 10/14/18 I have an early version of the inlet piping where it wasn't - MixManMash 12:14:41 10/14/18 Did somebody say "VBand Inlets"???? - ConVerTT 13:24:18 10/14/18 I'm throwing money at the screen... (n/m) - vorpalZ 10:48:36 10/15/18 LOL - your money's no good here .... - ConVerTT 15:06:19 10/15/18 Much yes. - BlackholeZ 21:50:01 10/15/18 Mani's will be quite a bit more difficult - ConVerTT 14:52:29 10/16/18 I'm really torn on what to do - BlackholeZ 22:02:08 10/17/18 Good plan (n/m) - ConVerTT 20:12:50 10/18/18 What would be ideal is a front clip so you can check - MixManMash 16:25:03 10/19/18 Yeah if I ever have a house with a shop - BlackholeZ 03:40:53 10/21/18 stock splash shield worked fine for me with the original - vorpalZ 00:51:47 10/12/18 sorry, meant air deflector not splash shield - vorpalZ 15:07:55 10/12/18 Anyone have a pic of that deflector installed - ZXoltan 16:17:58 10/12/18 You can see it in the tech article somewhat - spicyZ 21:52:01 10/12/18 Thanks. Was hoping for a view of exactly how it is attached (n/m) - ZXoltan 09:53:41 10/13/18 Insane just posted a decent picture. It bolts to the crash - MixManMash 08:55:12 10/19/18 *Inzane (n/m) - MixManMash 11:31:58 10/19/18 I run the Selin elbows and 370 filters without - not4resaleZ 09:03:31 10/13/18 Motorcycles don't have electronic MAFs (n/m) - Bernie (NoVA) 11:33:54 10/13/18 false (n/m) - vorpalZ 15:40:56 10/13/18 hush (n/m) - Bernie (NoVA) 18:10:20 10/13/18 not sure I understand your issue. Like VorpalZ said below - Inzane 11:55:34 10/18/18 Issue is... - GrecV2 15:18:17 10/18/18 Here's a pic of mine. - Inzane 23:35:15 10/18/18 I'm just not a fan of how much that blocks airflow. - not4resaleZ 10:10:36 10/19/18 you have to have a baffle or the direct airstream messes - vorpalZ 10:32:20 10/19/18 But my car runs great! See post above. (n/m) - not4resaleZ 10:39:51 10/19/18 I ran the baffle for years with the single pop, and then - not4resaleZ 10:57:01 10/19/18 if it's out of the direct airstream it is fine, the OP's - vorpalZ 11:04:03 10/19/18
Post a Followup	You cannot reply to this message because you are not logged in.