Subject	Lately I've ruined the threads on the stud before I was able
Posted by	BlackholeZ on October 11, 2018 at 9:46 PM
	This message has been viewed 314 times.
In Reply To	Meh ... posted by ConVerTT on October 10, 2018 at 12:02 PM
Message	to get the stud out. I've had to get some sprag clutch stud removers to remove them. Probably last 3 timing belts I've done. -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Knock sensor relocation? - jrocmoney99 23:08:38 10/08/18 here. - Bernie (NoVA) 00:33:24 10/09/18 The link Bernie sent is what you need. I'd also recommend - Waco300zx(DFW) 11:51:46 10/09/18 Re: The link Bernie sent is what you need. I'd also recommend - jrocmoney99 20:06:56 10/10/18 Not that I recommend this.. - Stanky (BC) 12:25:07 10/09/18 lol... I don't think anything is 'orthodox' on that Z - vorpalZ 12:36:57 10/09/18 What? How did I miss that? (n/m) - ConVerTT 13:25:34 10/09/18 Aggressive Port Work. Ports were larger than the seal on - MixManMash 13:31:18 10/09/18 ahh - yup - thanks! (n/m) - ConVerTT 13:39:49 10/09/18 Which fellow crazy canuck pulled that off?!?! (n/m) - Aqualung 14:22:58 10/09/18 I’ll wait for him to speak up .... (n/m) - ConVerTT 22:23:07 10/09/18 Dayum. (n/m) - spicyZ 14:22:59 10/09/18 whoa. (n/m) - Waco300zx(DFW) 14:49:18 10/09/18 Did he count the teeth between driver side exhaust and - MixManMash 15:09:24 10/09/18 Why not just unbolt the pulley? - Barry (NJ) 16:15:17 10/09/18 The idler stud is still there even if you remove the pulley (n/m) - i_s_64 17:59:17 10/09/18 ...and then you unscrew the stud. They are removable. (n/m) - Bernie (NoVA) 00:00:08 10/10/18 10 Years ago when I'd change them for timing belt jobs, - i_s_64 09:48:26 10/10/18 Meh ... - ConVerTT 12:02:38 10/10/18 Exactly what I've been doing on studs since 1994 - i_s_64 12:32:19 10/10/18 Agreed. No need to destroy the stud. (n/m) - ConVerTT 12:54:19 10/10/18 Pardon my ignorance, but... - ZXoltan 14:30:58 10/10/18 In his case it was an exhaust mani stud that he prematurely - i_s_64 17:20:08 10/10/18 Gotcha. Different case than the idler stud - ZXoltan 20:52:02 10/10/18 In the idler stud case .... - ConVerTT 23:49:43 10/10/18 Lately I've ruined the threads on the stud before I was able - BlackholeZ 21:46:49 10/11/18 I'd loose too much sleep over that one. (n/m) - Tanley (ATL) 07:57:08 10/10/18 Lord Tundering Jeesus there Boy. (n/m) - MeatMan (604Z) 10:09:42 10/11/18
Post a Followup	You cannot reply to this message because you are not logged in.