Subject	true true
Posted by	BlackholeZ on April 20, 2018 at 4:00 PM
	This message has been viewed 324 times.
In Reply To	hardware grade SS fastener UTS and YTS is less than 50% of posted by LitlElvis on April 20, 2018 at 11:47 AM
Message	And the stock screws are SOOO soft it's unbelievable. I was considering looking at the shear strength of those screws, because I too was concerned with using them like that. Using a standard SHCS is the proper solution. -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Cam lock tools - Rob260 06:03:59 04/16/18 Re: Cam lock tools - compirate 07:32:44 04/16/18 Great tool, but $150......ouch! (n/m) - The Hawk 09:47:44 04/16/18 After looking at that, I'm thinking of trying - Barry (NJ) 13:22:46 04/16/18 This might work a little better - ZXoltan 14:22:58 04/16/18 Re: Re: Cam lock tools - Rob260 15:54:39 04/16/18 Re: Re: Cam lock tools - Metacom 20:08:23 04/16/18 If the valve cover is off, use a wrench.... - SkiFly01 14:11:49 04/16/18 Re: If the valve cover is off, use a wrench.... - Rob260 15:56:25 04/16/18 True, unless you are replacing the valve cover gaskets / RTV - MixManMash 16:13:35 04/16/18 if you don't care about the T-belt, aka replacing it.... - SkiFly01 16:32:46 04/16/18 Some are of the opinion that impact gun may damage - ZXoltan 16:40:50 04/16/18 Re: if you don't care about the T-belt, aka replacing it.... - Rob260 17:10:33 04/16/18 Old belt? (n/m) - JMartz 16:47:45 04/16/18 Not that it's the "correct" way, but I impact them on/off. - Stanky (BC) 17:41:21 04/16/18 Re: Not that it's the "correct" way, but I impact them on/off. - Rob260 19:34:09 04/16/18 Re: Cam lock tools - VinZmax 07:18:23 04/17/18 Practically looks like it was designed that way... - Barry (NJ) 09:27:12 04/17/18 Re: Re: Cam lock tools - Rob260 21:12:46 04/17/18 Woody75 made a pretty cool setup with his 3D printer - LitlElvis 11:56:27 04/17/18 Shhhhh..... :) - Woody75 (Denver) 14:10:33 04/17/18 Color me impressed. Now hurry up and go make some of those. (n/m) - CameronSF 14:38:54 04/17/18 Cool! (n/m) - cherry 15:09:08 04/17/18 very crafty (n/m) - LJZTT 15:16:51 04/17/18 Love those Milwaukee ratchets! (n/m) - Stanky (BC) 17:59:06 04/17/18 Shoot me an email whenever you get around to making them - BlackholeZ 22:28:58 04/17/18 Willing to share the STL? (n/m) - Eric(NJ) 08:01:32 04/18/18 "Do not ask me to make you one or for the files" (n/m) - vorpalZ 12:36:19 04/18/18 I never claimed to read the whole post. ;) (n/m) - Eric(NJ) 13:33:50 04/18/18 ;) (n/m) - vorpalZ 16:02:08 04/18/18 Re: Shhhhh..... :) - supergoji 09:10:08 04/18/18 Well... - BlackholeZ 15:38:49 04/18/18 Can you make me one?..... :) - RobZ32 18:07:29 04/18/18 Amateur Z would be interested in one for the garage (n/m) - vorpalZ 20:23:47 04/18/18 Re: Woody75 made a pretty cool setup with his 3D printer - Rob260 21:15:10 04/17/18 I modified the spacers off my 300degree camber kit to work - Zbruh92 10:36:09 04/18/18 Can't see it (n/m) - supergoji 14:35:20 04/18/18 wanna borrow it? - Jiro 17:20:43 04/18/18 Looks ghetto, works great. $2 .... - ConVerTT 22:04:46 04/18/18 BTW - that “design” was inspired by a tool shown in the FSM - ConVerTT 23:40:21 04/18/18 I'd be afraid of breaking those thin bolts on the cover - ZXoltan 11:17:22 04/19/18 Me too. I guess one could source some bolts - MixManMash 19:48:03 04/19/18 hardware grade SS fastener UTS and YTS is less than 50% of - LitlElvis 11:47:18 04/20/18 ^What I was thinking, but Brett states it so eloquently ;-) (n/m) - ZXoltan 12:31:59 04/20/18 true true - BlackholeZ 16:00:36 04/20/18
Post a Followup	You cannot reply to this message because you are not logged in.