Subject	I have stock rods with ARPs pressed in and big ends resized
Posted by	ZaXxon on July 26, 2017 at 7:01 AM
	This message has been viewed 383 times.
In Reply To	That's what it looks like, but it's hard to say. posted by Stanky (BC) on July 25, 2017 at 08:35 PM
Message	And I'm running similar power levels. Hmmmm..... Not sure about the thou clearance comment, the ARPs are press fit, just like the stock bolts.
Follow Ups	Run 600ft-lbs on e85/stock rods they said..it'll be fun.. - Stanky (BC) 17:24:15 07/24/17 Wow... Back to the drawingboard. (n/m) - kickerzx 17:40:33 07/24/17 Uh oh! I sense forged internals in your near future. (n/m) - dfenton2 17:58:48 07/24/17 You'll need a few cans of brake clean and rags just - MixManMash 18:07:27 07/24/17 I suspect that the amount of torque at low RPMs that you - MixManMash 18:21:02 07/24/17 All the oil and coolant is on the highway lol - Stanky (BC) 19:09:09 07/24/17 will make an awesome engine block table, DO IT!! - LJZTT 16:20:25 07/26/17 It's actually what I plan on doing haha will post pics - Stanky (BC) 16:27:16 07/26/17 gonna be sweet, especially if you have some "Alien" -type - LJZTT 16:32:35 07/26/17 well you definitely out those shotpeened rods to the test. (n/m) - Boostjuice 18:26:37 07/24/17 PDR? (n/m) - LJZTT 18:28:07 07/24/17 Heartbreaking - Zsgetyoulaid 19:06:39 07/24/17 I knew that corn was gonna get you in trouble... - vorpalZ 20:06:53 07/24/17 The corn is a terrible influence.. - Stanky (BC) 22:25:27 07/24/17 I've got my torque plate all warmed up. lol (n/m) - dfenton2 01:10:57 07/25/17 Re: I knew that corn was gonna get you in trouble... - ConVerTT 08:28:40 07/25/17 Been there. - Boosted1 20:27:47 07/24/17 Re: Run 600ft-lbs on e85/stock rods they said..it'll be fun.. - Kvert 23:18:02 07/24/17 Once I pull the pan ill have a better idea - Stanky (BC) 23:21:55 07/24/17 ouch (n/m) - Madhatter10-6 08:11:35 07/25/17 well no one can say that you drove her like a princess :-) - ConVerTT 08:50:57 07/25/17 Hey, a set of used con bolts and some fiberglass - Zorpman 10:08:58 07/25/17 Dont forget the JB Weld and Duct Tape ;-) (n/m) - ZXoltan 18:19:35 07/25/17 Did the rod bolts fail? Or the actual rod? - ZaXxon 14:16:19 07/25/17 That's what it looks like, but it's hard to say. - Stanky (BC) 20:35:26 07/25/17 That looks very much like rod bolt failure. - Doug71zt(CAN) 06:36:36 07/26/17 FSM has incorrect rod bolt torque in some editions. - Doug71zt(CAN) 06:43:06 07/26/17 I have stock rods with ARPs pressed in and big ends resized - ZaXxon 07:01:00 07/26/17 Did you have ARP bolts for the rods? (n/m) - EZdusit (cali) 23:11:28 07/25/17 Yep, IIRC IPP uses ARP rod hardware on all his engines (n/m) - Stanky (BC) 23:37:26 07/25/17 interesting article on are VG head studs. - Boostjuice 12:34:05 07/26/17
Post a Followup	You cannot reply to this message because you are not logged in.