Subject	I'm not an expert, but I would consider increasing the
Posted by	not4resaleZ on October 15, 2015 at 3:42 PM
	This message has been viewed 534 times.
In Reply To	Here's what I came up with... posted by en5 on October 15, 2015 at 03:03 PM
Message	front bias slightly to account for quicker stopping and the resulting increased weight transfer. A jump to 75% by not doing the rears is probably way too much, but better than going to something like 55% bias where the rear axle would be locking up. Going from 63 to 65 may seem to be perfect, but then again, changes in ride height, tires, and other things could have made that 63% stock bias a somewhat poor setup. In my opinion, you will just have to test at the limit.
Follow Ups	Porsche 18z Calipers - DualZ (SF) 14:56:03 10/14/15 Re: Porsche 18z Calipers - zfreak(Dallas) 15:12:28 10/14/15 I have the 17Z, went with StopTech 1 piece rotors... - en5 17:16:56 10/14/15 Oh and before anyone yells... - en5 18:08:34 10/14/15 Just curious what is the brake bias you calculated for the - not4resaleZ 12:31:09 10/15/15 Here's what I came up with... - en5 15:03:37 10/15/15 I'm not an expert, but I would consider increasing the - not4resaleZ 15:42:42 10/15/15 Not Necessarily - Bad Fish 20:19:16 10/15/15 Sure - en5 21:10:59 10/15/15 Stock brakes will lock up anything you can fit under stock - LJZTT 19:21:55 10/16/15 30 minute pad change? Amateur... (n/m) - BigTDogg (MA) 21:25:26 10/19/15 Sometimes I forget all other cars may not be like mine. - not4resaleZ 09:38:36 10/16/15 bingo (n/m) - LJZTT 19:11:09 10/16/15 I have the adaptors and will be trying this as well someday. - Woody75 (Denver) 10:24:52 10/15/15 The only thing about the rockauto calipers - en5 15:23:58 10/15/15 I found another source for the cross over tubes. - Woody75 (Denver) 15:51:58 10/15/15 er... fix your tension rod (n/m) - vorpalZ 14:31:06 10/16/15 Re: Porsche 18z Calipers - EM.TT 12:28:34 10/15/15 Uh oh - when you do get them on let us know - en5 14:17:40 10/16/15 In some ways my opinion on brakes is similar to tires. - not4resaleZ 13:05:24 10/15/15 About 30 minutes worth of self-education on braking systems - LJZTT 11:57:06 10/16/15 Not sure why you're so up in arms over these BBK setups... - en5 13:57:36 10/16/15 I see your point en5 - DualZ (SF) 14:21:51 10/16/15 My post was directed towards LJZTT sorry for any confusion. (n/m) - en5 14:43:13 10/16/15 Re: - LJZTT 19:07:03 10/16/15 not sure why you think anyone is "up in arms" over anything - LJZTT 18:53:10 10/16/15 Re: Re: - en5 20:51:50 10/16/15 it's ok if you don't get it, you aren't the first (n/m) - LJZTT 11:53:35 10/17/15 That one guy in the post you linked really knows his stuff. (n/m) - not4resaleZ 14:27:11 10/16/15 Anyone consider using a brake proportioning valve? - DualZ (SF) 14:32:48 10/16/15 I looked into it, but IIRC it was explained to me that our - LJZTT 18:58:40 10/16/15
Post a Followup	You cannot reply to this message because you are not logged in.