Subject	Strange
Posted by	BlackholeZ on July 12, 2014 at 3:15 PM
	This message has been viewed 232 times.
In Reply To	Its the top bolt on every Z I have worked on. (n/m) posted by Woody75 (Denver) on July 11, 2014 at 02:19 PM
Message	I know you work on a lot of them. Maybe I'm mistaken. -Dan VTC Solenoid Caps and install instructions. "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Top Two Bolts on the Tranny - What a B1TCH! - Zbullet 22:31:16 07/10/14 14mm universal impact socket, 30" extension, impact gun (n/m) - Bernie (NoVA) 00:38:29 07/11/14 I actually find these fairly easy, i just get it from up top - Stanky 01:36:54 07/11/14 yes you gotta go from the top. get inside the car! (n/m) - Jiro 03:04:29 07/11/14 I can get on it with a wrench from the top BUT ... - Zbullet 07:04:09 07/11/14 i just leave the top two out (n/m) - Z32TT-R 01:38:21 07/11/14 Where do you secure the ground? (n/m) - Woody75 (Denver) 09:37:46 07/11/14 From Nissan it's the first one down on the pass side. (n/m) - BlackholeZ 12:40:50 07/11/14 Its the top bolt on every Z I have worked on. (n/m) - Woody75 (Denver) 14:19:32 07/11/14 Strange - BlackholeZ 15:15:46 07/12/14 tucked bay remember ;) batt out back. (n/m) - Z32TT-R 11:56:41 07/13/14 What you need is a wobble(universal) socket - ILoveBoost 07:23:48 07/11/14 yup. easy. (n/m) - Antihero 09:23:04 07/11/14 36 inch, 1/2 drive extension and a universal - JMartz 07:32:23 07/11/14 This. Except I use a 3/8 drive extension as it gives a - MixManMash 09:15:46 07/11/14 I use 3/8 too, I also remove the shifter bracket. - itsa300zx 11:08:14 07/11/14 yup... you have freaky double jointed arms... - vorpalZ 11:40:30 07/11/14 If you don't bolt the rear trans mount and.... - SkiFly01 11:34:21 07/11/14 2nd.... let the rear of the transmission droop - SammybTT(TN) 12:16:28 07/11/14 ah yes this is key. i assumed this was being done. - Jiro 10:02:39 07/12/14 PB Blaster...nectar of the gods (n/m) - LJZTT 12:59:44 07/11/14 To swear you got them all only to pull the engine with trans - LivinTheDream 15:44:35 07/11/14 SWIVEL SOCKET = My new best friend - Zbullet 20:32:46 07/13/14 A bit of duct tape around the universal swivel joint - intel 00:41:07 07/14/14
Post a Followup	You cannot reply to this message because you are not logged in.