Subject	yup... you have freaky double jointed arms...
Posted by	vorpalZ on July 11, 2014 at 11:40 AM
	This message has been viewed 197 times.
In Reply To	This. Except I use a 3/8 drive extension as it gives a posted by MixManMash on July 11, 2014 at 09:15 AM
Message	which means you get to undo the top two bolts... Yeah, yeah, life is unfair. MY Zs ARE HYBRID VEHICLES, THEY RUN ON GASOLINE AND MONEY "I expressed no attitude, I'm correcting you. If you don't like it, try not to be wrong next time. Now you're getting attitude, and if you don't like that you should grow a thicker skin.” - TriniTT 14:04:16 12/22/12 ”Exhaust doesn't produce horsepower” - VERTTZ 13:17:22 06/26/12 I'm off to wax mine and go for a drive now. - BigTDogg (MA) 07:17:08 07/17/09 times change, people change, but the Z32 still kicks ass. - apudapus 16:46:02 06/15/07 I was more wondering how you set your climate control to 22* lol, it would be that fastest freezer on wheels! - Briscoe'sZ32 (NJ) 23:15:44 02/05/07 You have *got* to be getting a cut from B&B :D - SeedyROM 15:24:29 08/16/06 What do you think B&B stands for? - YugoBernie (NoVA) 15:57:09 08/16/06
Follow Ups	Top Two Bolts on the Tranny - What a B1TCH! - Zbullet 22:31:16 07/10/14 14mm universal impact socket, 30" extension, impact gun (n/m) - Bernie (NoVA) 00:38:29 07/11/14 I actually find these fairly easy, i just get it from up top - Stanky 01:36:54 07/11/14 yes you gotta go from the top. get inside the car! (n/m) - Jiro 03:04:29 07/11/14 I can get on it with a wrench from the top BUT ... - Zbullet 07:04:09 07/11/14 i just leave the top two out (n/m) - Z32TT-R 01:38:21 07/11/14 Where do you secure the ground? (n/m) - Woody75 (Denver) 09:37:46 07/11/14 From Nissan it's the first one down on the pass side. (n/m) - BlackholeZ 12:40:50 07/11/14 Its the top bolt on every Z I have worked on. (n/m) - Woody75 (Denver) 14:19:32 07/11/14 Strange - BlackholeZ 15:15:46 07/12/14 tucked bay remember ;) batt out back. (n/m) - Z32TT-R 11:56:41 07/13/14 What you need is a wobble(universal) socket - ILoveBoost 07:23:48 07/11/14 yup. easy. (n/m) - Antihero 09:23:04 07/11/14 36 inch, 1/2 drive extension and a universal - JMartz 07:32:23 07/11/14 This. Except I use a 3/8 drive extension as it gives a - MixManMash 09:15:46 07/11/14 I use 3/8 too, I also remove the shifter bracket. - itsa300zx 11:08:14 07/11/14 yup... you have freaky double jointed arms... - vorpalZ 11:40:30 07/11/14 If you don't bolt the rear trans mount and.... - SkiFly01 11:34:21 07/11/14 2nd.... let the rear of the transmission droop - SammybTT(TN) 12:16:28 07/11/14 ah yes this is key. i assumed this was being done. - Jiro 10:02:39 07/12/14 PB Blaster...nectar of the gods (n/m) - LJZTT 12:59:44 07/11/14 To swear you got them all only to pull the engine with trans - LivinTheDream 15:44:35 07/11/14 SWIVEL SOCKET = My new best friend - Zbullet 20:32:46 07/13/14 A bit of duct tape around the universal swivel joint - intel 00:41:07 07/14/14
Post a Followup	You cannot reply to this message because you are not logged in.