Subject	It'd be a cool thing
Posted by	BlackholeZ on June 08, 2014 at 11:37 PM
	This message has been viewed 212 times.
In Reply To	That's unfortunate. (n/m) posted by Evan(CA) on June 08, 2014 at 08:19 PM
Message	but there are some differences between the coilovers. One I think is the space between detents. It might be the kind of thing that could be hacked to work, or even a mod made to make it easy. I haven't looked at how the EDFC adjusters mount. If I still had access to a machine shop I might be more into figuring it out. -Dan VTC Solenoid Caps and install instructions. "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Is it possible to make the Tein EDFC work with SPL coils? (n/m) - Evan(CA) 19:22:33 06/08/14 Short answer from Charles: - BlackholeZ 20:17:20 06/08/14 That's unfortunate. (n/m) - Evan(CA) 20:19:08 06/08/14 It'd be a cool thing - BlackholeZ 23:37:05 06/08/14 Re: Is it possible to make the Tein EDFC work with SPL coils? - Rob260 05:10:52 06/09/14 agreed...thats route i am going (n/m) - genic 08:30:16 06/09/14 Actually... I'm not sure I agree. - Antihero 16:19:38 06/09/14 Re: Actually... I'm not sure I agree. - Rob260 08:00:42 06/10/14 Re: Re: Actually... I'm not sure I agree. - Rob260 08:01:53 06/10/14 TEIN DSP46-KUSS2 Super Street - genic 09:07:23 06/10/14 big second. I have flex and I'm going to try out the ss on a - Dane (Houston) 23:53:50 06/10/14 It wouldn't be too hard to make a custom controller - Evan_Wright (Ca) 09:50:18 06/09/14 All though, if the only thing needed to make the tein EDFC - Evan_Wright (Ca) 10:01:33 06/09/14 don't forget the torque required to spin the spinny thing (n/m) - fuzzymonkey 12:40:11 06/09/14 That is certainly not the only thing needed. (n/m) - Antihero 15:59:32 06/09/14 I was thinking some better hobby servos (n/m) - BlackholeZ 13:43:17 06/09/14 Hobby servos could work if you understand how to - Evan_Wright (Ca) 14:01:24 06/09/14 Oh yeah it would need to go >360° - BlackholeZ 14:40:08 06/09/14 I haven't come across anything like that but you could - Evan_Wright (Ca) 15:26:27 06/09/14 It's a PWM setting - BlackholeZ 15:45:36 06/09/14 That sounds like fun. - Evan_Wright (Ca) 18:11:30 06/09/14 you can measure resistance at the motor... - Antihero 17:42:54 06/09/14 True. - Evan_Wright (Ca) 18:21:57 06/09/14 Yeah the servo control boards we had didn't have voltage - BlackholeZ 17:13:04 06/10/14
Post a Followup	You cannot reply to this message because you are not logged in.