Subject	That could actually be too high.
Posted by	BlackholeZ on June 08, 2014 at 3:44 PM
	This message has been viewed 301 times.
In Reply To	Room to work posted by 95TTurboZX on June 08, 2014 at 02:22 PM
Message	You might be able to sit under the car, so maybe not. There are a lot of times that you need to reach further up, like to the top of the bellhousing and getting it too high can make that stuff too hard to reach. -Dan VTC Solenoid Caps and install instructions. "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Room to work - 95TTurboZX 14:22:47 06/08/14 How did you get it up that high? (n/m) - Hipendicular 15:08:55 06/08/14 Thats what I am thinking. (n/m) - michaell32 (FL) 19:51:44 06/08/14 That could actually be too high. - BlackholeZ 15:44:23 06/08/14 Only need about half of what you have. - BoneZ (MD) 16:00:40 06/08/14 Where r u measuring 19" to? Pinchweld? (n/m) - ZXoltan 16:41:08 06/08/14 Pinchweld- lowest point of the body between the wheels. (n/m) - BoneZ (MD) 20:52:58 06/08/14 Re: Only need about half of what you have. - 95TTurboZX 15:27:18 06/09/14 Holy crap! - Evan_Wright (Ca) 16:25:11 06/08/14 thats exactly (creepy!) how i made my wood stands - genic 08:36:53 06/09/14 Re: thats exactly (creepy!) how i made my wood stands - 95TTurboZX 15:30:04 06/09/14 Kilroy was here... - BoneZ (MD) 18:56:40 06/09/14 I gotta make me a set of those still. (n/m) - Inzane 11:22:06 06/09/14 Z jenga (n/m) - XTZ 14:16:05 06/09/14 Impractical imo (n/m) - ali300zx 17:33:17 06/08/14 Looks like a lot of work to get it that high. - itsa300zx 18:12:04 06/08/14 Too high to pull engine/tranny (n/m) - ali300zx 18:39:27 06/08/14 nixit stands! 6 ton pittsburg stands from harbor freight - genic 08:33:44 06/09/14 I have these and they work grrrrrrr8! Plenty high enough. (n/m) - fuzzymonkey 12:27:30 06/09/14 That's to high you will regret it. To be honest - John (MD) 11:19:43 06/09/14 Re: That's to high you will regret it. To be honest - 95TTurboZX 15:38:10 06/09/14 I use both stands and blocks. (n/m) - BoneZ (MD) 18:58:06 06/09/14 Re: That's to high you will regret it. To be honest - WoodmanZ 22:31:26 06/10/14 love your plate - where are you located in NC? (n/m) - SuparexTT 14:41:53 06/09/14 Jacksonville (n/m) - 95TTurboZX 15:40:41 06/09/14
Post a Followup	You cannot reply to this message because you are not logged in.