Subject	Tried that with no joy. W/trans jack and w/o >>
Posted by	my91z on April 26, 2014 at 6:52 AM
	This message has been viewed 176 times.
In Reply To	Use the "bold with head cut off technique" posted by spicyZ on April 25, 2014 at 08:34 AM
Message	recentered using the tool a dozen time, brand new pilot bushing, even tapered the back end of the pilot bushing. Tried with and without tilting the engine, etc. Wiggling, jiggling, gets bolts started and trying to draw the two together, etc. I never destroyed a pilot bushing, so I couldn't have been too far off the mark. Nothing made it easy. I stabbed the trans two separate times (tears apart), and each was a never-ending, miserable experience. Other ppl tried, so it wasn't just my technique. The third time I knew I'd have to separate the engine and trans I dropped them together, and reinstalled them together. Not fun either, but better than the alternative, IMHO. I have dropping and replaced an E36 M3 trans and it was a piece of cake getting it stabbed compared to the Z. Mike -------------------------------------------------------- SRC="http://images.honesty.com/imagedata/h/402/36/24023634.j pg" BORDER=0> SRC="http://img718.imageshack.us/img718/4913/99m3ttnetsigpic 9564.jpg" BORDER=0>SRC="http://images.honesty.com/imagedata/h/365/13/23651377.g if" ALT="Click here to e-mail me!" BORDER=0>
Follow Ups	Finally Started NA>TT Swap! - tribalchild1 15:18:52 04/24/14 it only takes me an extra 15 minutes to remove the tranny - fuzzymonkey 17:01:03 04/24/14 It's stabbing the trans again afterwards that's the problem. (n/m) - my91z 19:41:29 04/24/14 Gotta learn how to 'stick it' in there kiddo. (n/m) - LivinTheDream 19:49:05 04/24/14 Re: Gotta learn how to 'stick it' in there kiddo. - Huber300zx 20:38:08 04/24/14 Sup. (n/m) - PennStateZ (NoVA) 22:08:44 04/24/14 Sup (n/m) - ZXRider 00:14:10 04/25/14 Still have a TT eh? (n/m) - PennStateZ (NoVA) 08:30:26 04/25/14 Yes sir. A big pain in my you know what, but still have it - ZXRider 13:55:37 04/25/14 2011 I think... - PennStateZ (NoVA) 12:42:27 04/26/14 Hey. (n/m) - my91z 12:59:39 04/26/14 Use the "bold with head cut off technique" - spicyZ 08:34:05 04/25/14 that, and ensure your pilot bushing is absolutely centered - vorpalZ 09:06:21 04/25/14 You mean clutch disc is absolutely centered. (n/m) - MixManMash 09:37:52 04/25/14 ... yes, and make sure you HAVE a pilot bushing :) (n/m) - vorpalZ 09:45:12 04/25/14 lol. Amazing how easy it is to stab the trans in without - MixManMash 12:15:01 04/25/14 I've used the plastic alignment tool dozens of times - BlackholeZ 13:25:20 04/25/14 agreed - aliaZ 13:29:32 04/25/14 Tried that with no joy. W/trans jack and w/o >> - my91z 06:52:31 04/26/14 Re: Finally Started NA>TT Swap! - sdvdoc 22:40:21 04/24/14 update on the tow loops for pulling motor. - tribalchild1 15:44:43 04/25/14
Post a Followup	You cannot reply to this message because you are not logged in.