TwinTurbo.NET: Nissan 300ZX forum - I've done several myself and know of several others who have
Subject
I've done several myself and know of several others who have
Posted by
Evan(CA)
on March 09, 2014 at 12:43 AM
This message has been viewed
266
times.
In Reply To
did I read that right? pullrd an engine with a tbelt?! (n/m)
posted by fuzzymonkey
on March 08, 2014 at 09:42 PM
Message
as well. It works fine but isn't very confidence inspiring.
Follow Ups
Engine Pull Question: Tools?
-
Bigwill837
18:08:09 03/07/14
PB Blaster, baggies, tie on labels, work light. (n/m)
-
280ZuL8r
18:14:19 03/07/14
Re: PB Blaster, baggies, tie on labels, work light.
-
Bigwill837
18:19:50 03/07/14
Re: Engine Pull Question: Tools?
-
jaidieray
18:19:10 03/07/14
Re: Re: Engine Pull Question: Tools?
-
Bigwill837
18:23:13 03/07/14
...er, stupid question.
-
Bigwill837
18:36:24 03/07/14
It can be done as one piece but seems a number
-
jzack
19:09:30 03/07/14
Also - if you get the tires off the ground about
-
jzack
19:41:47 03/07/14
IIRC 19" minimum for the trans to slide out from under (n/m)
-
BoneZ (MD)
19:55:59 03/07/14
Tires 19" off the ground? (n/m)
-
Tanley
23:21:58 03/07/14
lowest part of the body to the side of the trans, I.e. rails (n/m)
-
BoneZ (MD)
10:13:03 03/08/14
Thanks (n/m)
-
Tanley
10:19:18 03/08/14
Trans is 15 in. tall
-
-Grimm-
01:37:19 03/09/14
Thanks, I bought one of those harbor freight trans jacks and
-
Tanley
10:36:22 03/09/14
Getting to 25" is difficult, best to take it off the jack. (n/m)
-
BoneZ (MD)
11:32:57 03/10/14
I put the Z on the stands high enough to unbolt the trans
-
Woody75 (Denver)
14:47:15 03/10/14
Thanks for the advice guys. (n/m)
-
Tanley
21:03:21 03/10/14
I've done it both ways
-
-Grimm-
20:45:51 03/07/14
i've done it on all ways, and the best way is to
-
fuzzymonkey
21:41:24 03/08/14
I'd like to know if a load leveler is helpful with the
-
Evan(CA)
18:44:20 03/07/14
2nd on the Ramey Z sling.... (n/m)
-
jzack
19:13:46 03/07/14
did I read that right? pullrd an engine with a tbelt?! (n/m)
-
fuzzymonkey
21:42:57 03/08/14
I've done several myself and know of several others who have -
Evan(CA)
00:43:16 03/09/14
An old seat belt works much better. (n/m)
-
BradX (UF)
16:06:54 03/09/14
Beer/Smokes/Snacks (n/m)
-
BoneZ (MD)
19:55:03 03/07/14
Looks like you have it about covered... don't forget this
-
Piranha
20:09:43 03/07/14
Hey Shane
-
Evan(CA)
20:43:29 03/07/14
No I just used the RameyZ sling
-
Piranha
21:23:54 03/07/14
How are you liking the stand alone? (n/m)
-
The Hawk
11:42:39 03/08/14
It's in the works along with RPS carbon carbon and
-
Piranha
16:14:50 03/08/14
Glad things are working well for you, but....
-
The Hawk
17:04:20 03/08/14
Oh you got me... hopefully I'm as wise as you someday
-
Piranha
17:42:02 03/08/14
The plain facts are...
-
The Hawk
11:55:04 03/09/14
Ok scooter McGee: scavenger hunter... since you like to play
-
Piranha
13:10:55 03/09/14
I'm just not fond of hypocrites
-
The Hawk
13:38:29 03/09/14
No I was playing football while you were on the debate
-
Piranha
13:42:18 03/09/14
Nope. Don't think I'll drive 2.5K miles for that one...
-
The Hawk
16:29:32 03/09/14
Also, what kind of #'s did you make w/ the new set-up?
-
The Hawk
14:11:22 03/08/14
I'm running a pretty safe chip now from Greg until I get
-
Piranha
16:05:30 03/08/14
Re: Looks like you have it about covered... don't forget this
-
Bigwill837
22:23:37 03/07/14
Yea Damon knows his stuff! I used it mainly as reference
-
Piranha
18:28:22 03/08/14
A good quality fender cover to save your paint. (n/m)
-
itsa300zx
20:21:11 03/07/14
14mm crows foot for the AC compressor's rear basterd bolt
-
Stanky
01:01:27 03/08/14
And the snowball begins to roll... (n/m)
-
Broke_as_****
03:05:00 03/08/14
I used the engine leveler with out the RameyZ sling
-
SammybTT(TN)
08:43:43 03/08/14
I apologize for jacking your thread up there :(
-
Piranha
18:15:43 03/08/14
Re: I apologize for jacking your thread up there :(
-
wild_maxx
20:26:20 03/08/14
Transmission jack
-
ZaXxon
10:24:26 03/09/14
Post a
Followup
You cannot reply to this message because you are not
logged in
.