Subject	Thanks (n/m)
Posted by	Tanley on March 08, 2014 at 10:19 AM
	This message has been viewed 267 times.
In Reply To	lowest part of the body to the side of the trans, I.e. rails (n/m) posted by BoneZ (MD) on March 08, 2014 at 10:13 AM
Message
Follow Ups	Engine Pull Question: Tools? - Bigwill837 18:08:09 03/07/14 PB Blaster, baggies, tie on labels, work light. (n/m) - 280ZuL8r 18:14:19 03/07/14 Re: PB Blaster, baggies, tie on labels, work light. - Bigwill837 18:19:50 03/07/14 Re: Engine Pull Question: Tools? - jaidieray 18:19:10 03/07/14 Re: Re: Engine Pull Question: Tools? - Bigwill837 18:23:13 03/07/14 ...er, stupid question. - Bigwill837 18:36:24 03/07/14 It can be done as one piece but seems a number - jzack 19:09:30 03/07/14 Also - if you get the tires off the ground about - jzack 19:41:47 03/07/14 IIRC 19" minimum for the trans to slide out from under (n/m) - BoneZ (MD) 19:55:59 03/07/14 Tires 19" off the ground? (n/m) - Tanley 23:21:58 03/07/14 lowest part of the body to the side of the trans, I.e. rails (n/m) - BoneZ (MD) 10:13:03 03/08/14 Thanks (n/m) - Tanley 10:19:18 03/08/14 Trans is 15 in. tall - -Grimm- 01:37:19 03/09/14 Thanks, I bought one of those harbor freight trans jacks and - Tanley 10:36:22 03/09/14 Getting to 25" is difficult, best to take it off the jack. (n/m) - BoneZ (MD) 11:32:57 03/10/14 I put the Z on the stands high enough to unbolt the trans - Woody75 (Denver) 14:47:15 03/10/14 Thanks for the advice guys. (n/m) - Tanley 21:03:21 03/10/14 I've done it both ways - -Grimm- 20:45:51 03/07/14 i've done it on all ways, and the best way is to - fuzzymonkey 21:41:24 03/08/14 I'd like to know if a load leveler is helpful with the - Evan(CA) 18:44:20 03/07/14 2nd on the Ramey Z sling.... (n/m) - jzack 19:13:46 03/07/14 did I read that right? pullrd an engine with a tbelt?! (n/m) - fuzzymonkey 21:42:57 03/08/14 I've done several myself and know of several others who have - Evan(CA) 00:43:16 03/09/14 An old seat belt works much better. (n/m) - BradX (UF) 16:06:54 03/09/14 Beer/Smokes/Snacks (n/m) - BoneZ (MD) 19:55:03 03/07/14 Looks like you have it about covered... don't forget this - Piranha 20:09:43 03/07/14 Hey Shane - Evan(CA) 20:43:29 03/07/14 No I just used the RameyZ sling - Piranha 21:23:54 03/07/14 How are you liking the stand alone? (n/m) - The Hawk 11:42:39 03/08/14 It's in the works along with RPS carbon carbon and - Piranha 16:14:50 03/08/14 Glad things are working well for you, but.... - The Hawk 17:04:20 03/08/14 Oh you got me... hopefully I'm as wise as you someday - Piranha 17:42:02 03/08/14 The plain facts are... - The Hawk 11:55:04 03/09/14 Ok scooter McGee: scavenger hunter... since you like to play - Piranha 13:10:55 03/09/14 I'm just not fond of hypocrites - The Hawk 13:38:29 03/09/14 No I was playing football while you were on the debate - Piranha 13:42:18 03/09/14 Nope. Don't think I'll drive 2.5K miles for that one... - The Hawk 16:29:32 03/09/14 Also, what kind of #'s did you make w/ the new set-up? - The Hawk 14:11:22 03/08/14 I'm running a pretty safe chip now from Greg until I get - Piranha 16:05:30 03/08/14 Re: Looks like you have it about covered... don't forget this - Bigwill837 22:23:37 03/07/14 Yea Damon knows his stuff! I used it mainly as reference - Piranha 18:28:22 03/08/14 A good quality fender cover to save your paint. (n/m) - itsa300zx 20:21:11 03/07/14 14mm crows foot for the AC compressor's rear basterd bolt - Stanky 01:01:27 03/08/14 And the snowball begins to roll... (n/m) - Broke_as_**** 03:05:00 03/08/14 I used the engine leveler with out the RameyZ sling - SammybTT(TN) 08:43:43 03/08/14 I apologize for jacking your thread up there :( - Piranha 18:15:43 03/08/14 Re: I apologize for jacking your thread up there :( - wild_maxx 20:26:20 03/08/14 Transmission jack - ZaXxon 10:24:26 03/09/14
Post a Followup	You cannot reply to this message because you are not logged in.