Subject	It is my belief that the rearmost cylinders are so
Posted by	Ash's Z on March 03, 2014 at 11:31 PM
	This message has been viewed 467 times.
In Reply To	Guess it beats coming out of the meth lab :-P posted by ZXoltan on March 03, 2014 at 11:26 PM
Message	detonation prone being a result of two primary factors: 1) The induction system, namely the plenum design, will promote better airflow into these cylinders. 2) The cooling system, by the introduction of the "coolest" coolant coming to the front of the engine and having to make its way through hot cast iron on its way to the rearmost cylinders which also have not only the least pressure differential to move the water, but also a huge bias of flow between the driver/passenger sides by way of the heater core circulation system.... *gasp* Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	Straight out of the mad lab.... >> - Ash's Z 22:52:17 03/03/14 Guess it beats coming out of the meth lab :-P - ZXoltan 23:26:31 03/03/14 It is my belief that the rearmost cylinders are so - Ash's Z 23:31:32 03/03/14 ... which BTW I have a system that addresses the last issue - Ash's Z 23:33:16 03/03/14 Details on that system? (n/m) - BarryGZX 00:54:22 03/04/14 Seems as if it wouldn't be too hard to come up with a - jzack 18:53:42 03/04/14 The solution I built is nothing of the sort... Quite a bit - Ash's Z 14:55:00 03/05/14 can you be any more vague? (n/m) - aliaZ 18:16:57 03/05/14 I'm sure I can... :) I've already designed all of the parts - Ash's Z 23:02:26 03/05/14 does this mod make the engine run cooler overall? - aliaZ 07:43:02 03/06/14 The heater core has a valve that prevents flow through it - LitlElvis 17:43:53 03/07/14 I had bypassed my heater core last summer - BarryGZX 00:28:29 03/04/14 I was thinking it was due to the unequal length of the - ZXoltan 05:36:18 03/04/14 I agree - aliaZ 06:28:56 03/04/14 Re: It is my belief that the rearmost cylinders are so - induetime 10:41:06 03/04/14 Did you ever model the flattened 6th runner? - BlackholeZ 13:51:25 03/04/14 interesting, please do repeat with larger valve / porting (n/m) - JaffaUK 00:33:02 03/04/14 2nd (n/m) - BoneZ (MD) 07:47:41 03/04/14 Sweet! Consistency is very good - BlackholeZ 03:17:20 03/04/14 Good stuff. ETA on release, cost and fit? (n/m) - BigTDogg (MA) 09:24:55 03/04/14 lol (n/m) - aliaZ 16:19:20 03/05/14 How does the surface roughness of your 3D model compare to - LitlElvis 13:22:03 03/04/14 Standard 3D printing - BlackholeZ 13:49:30 03/04/14 Its about the same really. This was printed with a 0.007" - Ash's Z 15:11:27 03/04/14
Post a Followup	You cannot reply to this message because you are not logged in.