Subject	I just asked my machinist about this
Posted by	ZXoltan on January 29, 2014 at 1:44 PM
	This message has been viewed 346 times.
In Reply To	Re: Here's where my rebuild ignorance may shine, but does posted by wild_maxx on January 29, 2014 at 12:36 PM
Message	He said the nitriding goes down about .200 If they need to go to undersize bearings because of journal damage they usually turn the cranks down .010- .020 Technically there should be plenty left, but most of us would opt to use a standard crank for good measure
Follow Ups	Just completed my first rebuild. Lots of pics... - wild_maxx 22:00:45 01/28/14 Looks great, congrats. (n/m) - Turbonium 300Zx 23:12:10 01/28/14 Very nice. Did you check/ adjust piston ring end gap? - ZXoltan 23:13:45 01/28/14 Re: Very nice. Did you check/ adjust piston ring end gap? - wild_maxx 06:51:35 01/29/14 Awesome! Which ring filer did you use? - ZXoltan 08:22:11 01/29/14 wow well done! Thanks for sharing, love these threads (n/m) - Stanky 23:19:36 01/28/14 Great job. Thanks for sharing. (n/m) - Evan_Wright (Ca) 23:37:27 01/28/14 Very nice!! - BlackholeZ 00:04:14 01/29/14 nice ! (n/m) - The Devils Z 00:10:39 01/29/14 Sweet job, plenum color looks great, can't wait to see more - ConverTTZ 01:47:11 01/29/14 way to go! (n/m) - moxie (SF) 01:52:01 01/29/14 Friggn awesome! (n/m) - BarryGZX 02:43:58 01/29/14 Awesome! For your oil feed lines - BoneZ (MD) 06:44:19 01/29/14 Re: Awesome! For your oil feed lines - wild_maxx 07:10:06 01/29/14 I'm putting stock turbos back on the car and was concerned - BoneZ (MD) 07:29:30 01/29/14 The stock lines use a restrictor in the banjo on pass side - Greg D. (Specialty-Z) 14:56:09 01/29/14 Just looked at the CZP kit for stock turbos...... - Greg D. (Specialty-Z) 15:11:12 01/29/14 Re: Just looked at the CZP kit for stock turbos...... - wild_maxx 15:56:43 01/29/14 No worries, Congrats!!! (n/m) - Greg D. (Specialty-Z) 16:08:47 01/29/14 That clears it up - I'd prefer to run the same setup - BoneZ (MD) 20:37:45 01/29/14 Thanks Greg! (n/m) - BoneZ (MD) 20:35:26 01/29/14 I have that kit as well - -Grimm- 12:59:09 01/30/14 Looks great! - coreymbassett 07:54:18 01/29/14 Re: Looks great! - wild_maxx 08:13:45 01/29/14 From one PGY owner to another, well done sir. - Aqualung 08:40:31 01/29/14 Nice, can't wait to see final product. Keep us tuned in (n/m) - 300ZMang 09:21:24 01/29/14 Very impressive! That's a lot of work. - cherry 09:25:23 01/29/14 Excellent job...love the color scheme...Enjoy (n/m) - RobZ32 09:55:43 01/29/14 Nice! Hell of a first rebuild (n/m) - Madhatter10-6 10:13:14 01/29/14 Great job, it's a keeper (n/m) - TTZ2NV(EPTmotorsports) 10:19:57 01/29/14 Great job! (n/m) - Jayru 10:48:50 01/29/14 Thanks for sharing. (n/m) - BlitZ91TT 11:04:35 01/29/14 very nice job. looks great!! (n/m) - fst300zx 11:32:33 01/29/14 Thanks for all the pictures. (n/m) - GatorJ 11:55:52 01/29/14 Here's where my rebuild ignorance may shine, but does - zgene4 12:16:37 01/29/14 Re: Here's where my rebuild ignorance may shine, but does - wild_maxx 12:36:46 01/29/14 I just asked my machinist about this - ZXoltan 13:44:06 01/29/14 Not true...... - Greg D. (Specialty-Z) 16:07:54 01/29/14 Thanks Greg. I wonder what else he is clueless about :-O (n/m) - ZXoltan 17:08:06 01/29/14 Looks beautiful. - rojoloco (VA Beach) 13:10:34 01/29/14 Re: Looks beautiful. - wild_maxx 13:55:44 01/29/14 Yeah, he did the swap. - rojoloco (VA Beach) 22:21:39 01/29/14 excellent post, congrats (n/m) - Ahmed (NoVA) 13:35:05 01/29/14 awesome, wish I had the knowledge/know-how to build engines (n/m) - LJZTT 14:45:43 01/29/14 beautiful engine! Great post ! Congrats! (n/m) - 300zxNA2TT 14:47:57 01/29/14 Nice work. Looks good. (n/m) - Boosted1 18:44:45 01/29/14 Awesome work. You are making me get the itch :-) - ConVerTT 19:42:16 01/29/14 Exceeded views? No pics. Use Flickr next time. (n/m) - PiotrC70 20:08:52 01/29/14 Re: Exceeded views? No pics. Use Flickr next time. - wild_maxx 20:14:17 01/29/14 Amazing. Clearly AJ Hawk is pumped about it, too! (n/m) - Stokens (AR) 20:46:26 01/29/14 Looking good, I need to quit being so lazy and post mine - SammybTT(TN) 22:19:57 01/29/14 About time you have it done. Good works! (n/m) - StramanVerTT(GA) 09:31:18 01/30/14 That looks awesome, nice work! (n/m) - BigTDogg (MA) 10:01:15 01/30/14
Post a Followup	You cannot reply to this message because you are not logged in.