Subject	must have run out of patience at that point
Posted by	vorpalZ on January 27, 2014 at 1:47 PM
	This message has been viewed 379 times.
In Reply To	2nd. When I reinstalled the new harness, I was posted by 300MPH on January 27, 2014 at 01:04 PM
Message	I could get every bracket on and all but 1 shield, the lowest one below the BMC. Plenum was on both motors as well, just for extra fun. Cheers, MY Zs ARE HYBRID VEHICLES, THEY RUN ON GASOLINE AND MONEY "I expressed no attitude, I'm correcting you. If you don't like it, try not to be wrong next time. Now you're getting attitude, and if you don't like that you should grow a thicker skin.” - TriniTT 14:04:16 12/22/12 ”Exhaust doesn't produce horsepower” - VERTTZ 13:17:22 06/26/12 I'm off to wax mine and go for a drive now. - BigTDogg (MA) 07:17:08 07/17/09 times change, people change, but the Z32 still kicks ass. - apudapus 16:46:02 06/15/07 I was more wondering how you set your climate control to 22* lol, it would be that fastest freezer on wheels! - Briscoe'sZ32 (NJ) 23:15:44 02/05/07 You have *got* to be getting a cut from B&B :D - SeedyROM 15:24:29 08/16/06 What do you think B&B stands for? - YugoBernie (NoVA) 15:57:09 08/16/06
Follow Ups	WS wiring harness install with engine/trans still in car. I - Haasz32 10:57:07 01/27/14 Nice!!!! We're you able to put back all the - TTZ2NV(EPTmotorsports) 11:11:08 01/27/14 I didn't get all every bracket back the same as it was. - Haasz32 11:29:33 01/27/14 Yes it is possible. It will take a lot of patience and - ZXRider 12:28:05 01/27/14 I've also done it... - vorpalZ 11:11:59 01/27/14 I must have got lucky since I was able to get - ZXRider 12:27:16 01/27/14 2nd. When I reinstalled the new harness, I was - 300MPH 13:04:12 01/27/14 must have run out of patience at that point - vorpalZ 13:47:16 01/27/14 Same here: plenum on, EGR in place, BMC in place, etc. - Haasz32 14:01:43 01/27/14 I got mine on too, but I dont recall if I completely removed - LJZTT 14:32:39 01/27/14 I was definitely out of patience too. I had the - 300MPH 15:57:26 01/27/14 FYI, you don't have to disconnect AC during engine pull - bartz32tt 11:28:02 01/27/14 OK, that's good to know for when I do need to pull the - Haasz32 11:31:54 01/27/14 If you do have to drain freon, check out R12a - ThisIsSparTTa 12:56:13 01/27/14 I did it once, never do it again - ZXRider 12:29:12 01/27/14 How did you get the subharnesses through the firewall? - type993 12:51:18 01/27/14 De-pin the white connector - ZXRider 12:55:15 01/27/14 Yeah that's what I figured.. - type993 13:56:46 01/27/14 I have the version where the white sub-harness has the quick - Haasz32 13:21:40 01/27/14 According to Bernie that grey box is a loop block - ZXRider 13:45:25 01/27/14 Yeah, I wonder if it isn't the same principle as the wire - Haasz32 13:57:10 01/27/14 I have never had trouble getting them through the FW (n/m) - Bernie (NoVA) 04:47:20 01/28/14 I got the initial EFI version (before WS fixed it) :( (n/m) - type993 14:04:41 01/27/14
Post a Followup	You cannot reply to this message because you are not logged in.