Subject	De-pin the white connector
Posted by	ZXRider on January 27, 2014 at 12:55 PM
	This message has been viewed 366 times.
In Reply To	How did you get the subharnesses through the firewall? posted by type993 on January 27, 2014 at 12:51 PM
Message	I wrapped the blue connector with plastic and seran wrap to protect it, and de-pinned the white connector after marking all the wires, taking pictures and drawing diagrams for myself. It also helps to make sure you have the wiring diagram for it so you know how to put everything back together properly. Buy Zama Posters Here I have nightmares about that happening...I'd be the poor bastard you'd hear about on the news that gets killed by a softball-size chunk while spreading out my body over the hood and screaming "Nooo!" (Having a conversation about hail damage) - BradZ (FL) on March 25, 2005 at 9:56 PM Tell your friend that you could take a dump, light it on fire and that would be hotter shit than his car. Probes suck, that's just all there is to it. - 300ZXpert (someday) on April 04, 2005 at 11:35 PM P.S. You REALLY are on here at ALL hours! And I thought I was bad! :) - zmenon on August 16, 2005 at 3:06 AM LOL...2+2 drivers should grow mullets..."Business in the front...party in the back" ;) - BradZ (FL) on November 29, 2005 at 4:45 PM
Follow Ups	WS wiring harness install with engine/trans still in car. I - Haasz32 10:57:07 01/27/14 Nice!!!! We're you able to put back all the - TTZ2NV(EPTmotorsports) 11:11:08 01/27/14 I didn't get all every bracket back the same as it was. - Haasz32 11:29:33 01/27/14 Yes it is possible. It will take a lot of patience and - ZXRider 12:28:05 01/27/14 I've also done it... - vorpalZ 11:11:59 01/27/14 I must have got lucky since I was able to get - ZXRider 12:27:16 01/27/14 2nd. When I reinstalled the new harness, I was - 300MPH 13:04:12 01/27/14 must have run out of patience at that point - vorpalZ 13:47:16 01/27/14 Same here: plenum on, EGR in place, BMC in place, etc. - Haasz32 14:01:43 01/27/14 I got mine on too, but I dont recall if I completely removed - LJZTT 14:32:39 01/27/14 I was definitely out of patience too. I had the - 300MPH 15:57:26 01/27/14 FYI, you don't have to disconnect AC during engine pull - bartz32tt 11:28:02 01/27/14 OK, that's good to know for when I do need to pull the - Haasz32 11:31:54 01/27/14 If you do have to drain freon, check out R12a - ThisIsSparTTa 12:56:13 01/27/14 I did it once, never do it again - ZXRider 12:29:12 01/27/14 How did you get the subharnesses through the firewall? - type993 12:51:18 01/27/14 De-pin the white connector - ZXRider 12:55:15 01/27/14 Yeah that's what I figured.. - type993 13:56:46 01/27/14 I have the version where the white sub-harness has the quick - Haasz32 13:21:40 01/27/14 According to Bernie that grey box is a loop block - ZXRider 13:45:25 01/27/14 Yeah, I wonder if it isn't the same principle as the wire - Haasz32 13:57:10 01/27/14 I have never had trouble getting them through the FW (n/m) - Bernie (NoVA) 04:47:20 01/28/14 I got the initial EFI version (before WS fixed it) :( (n/m) - type993 14:04:41 01/27/14
Post a Followup	You cannot reply to this message because you are not logged in.