Subject	OEM Zs also have HICAS, PRVR, AIV, non switched power
Posted by	michaell32 (FL) on January 03, 2014 at 11:26 AM
	This message has been viewed 213 times.
In Reply To	Re: Oem is beaded posted by Rob260 on January 02, 2014 at 11:46 PM
Message	for most of the years, a poor pcv setup, and a single intake. But what do they know right. I like the fact that the inlet pipes are not beaded. It makes them easier to install and remove. Ive yet to have a single leak on the inlet pipes on my car. KongZTT GT28RS MD "I was very impressed with his mother mounts" Aliaz "I always shave down the boss when I do headwork" 240Z FeO2 "It's the way this forums weeds out morons, whiners and the pathetically light weight. According to AMS duplication = innovation
Follow Ups	AshSpec Inlet Pipes - Bad Fish 12:29:45 01/02/14 No beading at the ends? - ZXoltan 13:58:48 01/02/14 Re: No beading at the ends? - Bad Fish 14:14:02 01/02/14 Those may have been blems or earlier prototypes that - ZXoltan 14:54:42 01/02/14 I asked Nick about the beadless inlet pipes when he still - Evan_Wright (Ca) 14:59:44 01/02/14 Truth... - ConVerTT 16:01:42 01/02/14 +1 - No need for them - Jayru 16:25:08 01/02/14 just a FYI, I have found while dealing with intake hardpipes - LJZTT 18:26:53 01/02/14 Good to know. The grease did make quite a mess. (n/m) - Jayru 22:10:52 01/02/14 I use brakeclean on silicone. Slick for a few seconds then - ztunerz 23:09:42 01/02/14 False. Inlets do not have beads. - ConVerTT 15:57:24 01/02/14 :0 (n/m) - Krazyd27(Houston) 16:01:17 01/02/14 Thanks. I stand corrected. And now I dont even want to own - ZXoltan 18:51:23 01/02/14 Re: Thanks. I stand corrected. And now I dont even want to own - Rob260 22:33:22 01/02/14 Oem is beaded (n/m) - ztunerz 23:08:23 01/02/14 Re: Oem is beaded - Rob260 23:46:57 01/02/14 OEM Zs also have HICAS, PRVR, AIV, non switched power - michaell32 (FL) 11:26:28 01/03/14 Because it's cheaper to cut corners. (n/m) - Bernie (NoVA) 09:38:50 01/03/14 They work fine. The couplers really grip the pipes. They - ConVerTT 10:23:02 01/03/14 "work fine" isn't the point. - Bernie (NoVA) 10:54:51 01/03/14 Ok, but "saving cost" does not necessarily mean "cutting - ConVerTT 11:13:26 01/03/14 Honestly I would pay a few bux to have it beaded. - ztunerz 17:45:49 01/03/14 If they had a bead, a larger dia hose would not get stuck? - Brad(RI) 10:31:56 01/04/14 LOL - yes you do :-) (n/m) - ConVerTT 11:14:58 01/03/14 Inlets are not beaded, just make sure you have the - CmyZ 18:35:18 01/02/14
Post a Followup	You cannot reply to this message because you are not logged in.