Subject	Per JWT current web page, All billet cams come with the
Posted by	Brad(RI) on January 02, 2014 at 6:21 PM
	This message has been viewed 231 times.
In Reply To	They don't unless its a newer change they made. posted by Woody75 (Denver) on January 02, 2014 at 10:30 AM
Message	upgraded CrMo pin. I guess that means regrinds don't maybe. I actually got my pin through CZP and I have access to an XRF metal analyzer with which I can determine the exact composition of the alloy. I thought about testing the pin before I put it in, but I decided to have faith lol. Hopefully that was a good decision.
Follow Ups	I am Spartacus - Brad(RI) 22:26:42 12/31/13 lol. Stay off the steroids. (n/m) - ForceFedTT (SoCal) 00:45:19 01/01/14 Do you have the new one installed? (n/m) - Alan (TN) 01:45:25 01/01/14 Yes, all installed - Brad(RI) 09:43:17 01/01/14 did you use a 5mm drill bit and drill it out with the motor - LJZTT 13:01:30 01/01/14 No, I was doing the timing belt so - Brad(RI) 13:53:21 01/01/14 there has got to be a good way to remove it w/out - LJZTT 20:21:47 01/01/14 You need to check the spline on your CAS. Worn spline - Alan (TN) 14:14:16 01/01/14 I checked it yes, it only has about 2,000 miles on it - Brad(RI) 14:48:32 01/01/14 ugh, I have to do this as well (n/m) - LJZTT 02:31:37 01/01/14 What material is this made from? - bartz32tt 10:08:52 01/01/14 The replacment is Chrome Moly - Brad(RI) 10:18:39 01/01/14 Sorry but I don't recognize this part - SammybTT(TN) 10:22:17 01/01/14 Here is a link that discusses this issue and the cure - Brad(RI) 10:42:18 01/01/14 I guess the photo threw me off - SammybTT(TN) 11:37:43 01/01/14 it doesn't have to get worn down exclusively for the reasons - LJZTT 12:40:21 01/01/14 The misalignment issues is theoretically limited to early - Brad(RI) 13:35:15 01/01/14 The grease is in there more to seal out moisture - ZXoltan 18:23:24 01/01/14 Is this only an issue on some z32's or all? (n/m) - VERTTZ 11:16:17 01/01/14 according to JWT early 90 models if it results from the - LJZTT 12:59:46 01/01/14 Ah. Well I just read that all of the JWT camshafts come with - VERTTZ 16:53:32 01/01/14 If your cam mount is misaligned you're likely to - ZXoltan 18:17:21 01/01/14 I would think you could still have this happen, but that - LJZTT 20:24:25 01/01/14 I had to replace the spline in a set of JWT cams. I believe - Alan (TN) 22:22:19 01/01/14 They don't unless its a newer change they made. - Woody75 (Denver) 10:30:54 01/02/14 Per JWT current web page, All billet cams come with the - Brad(RI) 18:21:03 01/02/14
Post a Followup	You cannot reply to this message because you are not logged in.