TwinTurbo.NET: Nissan 300ZX forum - You need to check the spline on your CAS. Worn spline
Subject
You need to check the spline on your CAS. Worn spline
Posted by
Alan (TN)
on January 01, 2014 at 2:14 PM
This message has been viewed
256
times.
In Reply To
Yes, all installed
posted by Brad(RI)
on January 01, 2014 at 09:43 AM
Message
Teeth on your CAS will recreate the situation you just fixed.
Follow Ups
I am Spartacus
-
Brad(RI)
22:26:42 12/31/13
lol. Stay off the steroids. (n/m)
-
ForceFedTT (SoCal)
00:45:19 01/01/14
Do you have the new one installed? (n/m)
-
Alan (TN)
01:45:25 01/01/14
Yes, all installed
-
Brad(RI)
09:43:17 01/01/14
did you use a 5mm drill bit and drill it out with the motor
-
LJZTT
13:01:30 01/01/14
No, I was doing the timing belt so
-
Brad(RI)
13:53:21 01/01/14
there has got to be a good way to remove it w/out
-
LJZTT
20:21:47 01/01/14
You need to check the spline on your CAS. Worn spline -
Alan (TN)
14:14:16 01/01/14
I checked it yes, it only has about 2,000 miles on it
-
Brad(RI)
14:48:32 01/01/14
ugh, I have to do this as well (n/m)
-
LJZTT
02:31:37 01/01/14
What material is this made from?
-
bartz32tt
10:08:52 01/01/14
The replacment is Chrome Moly
-
Brad(RI)
10:18:39 01/01/14
Sorry but I don't recognize this part
-
SammybTT(TN)
10:22:17 01/01/14
Here is a link that discusses this issue and the cure
-
Brad(RI)
10:42:18 01/01/14
I guess the photo threw me off
-
SammybTT(TN)
11:37:43 01/01/14
it doesn't have to get worn down exclusively for the reasons
-
LJZTT
12:40:21 01/01/14
The misalignment issues is theoretically limited to early
-
Brad(RI)
13:35:15 01/01/14
The grease is in there more to seal out moisture
-
ZXoltan
18:23:24 01/01/14
Is this only an issue on some z32's or all? (n/m)
-
VERTTZ
11:16:17 01/01/14
according to JWT early 90 models if it results from the
-
LJZTT
12:59:46 01/01/14
Ah. Well I just read that all of the JWT camshafts come with
-
VERTTZ
16:53:32 01/01/14
If your cam mount is misaligned you're likely to
-
ZXoltan
18:17:21 01/01/14
I would think you could still have this happen, but that
-
LJZTT
20:24:25 01/01/14
I had to replace the spline in a set of JWT cams. I believe
-
Alan (TN)
22:22:19 01/01/14
They don't unless its a newer change they made.
-
Woody75 (Denver)
10:30:54 01/02/14
Per JWT current web page, All billet cams come with the
-
Brad(RI)
18:21:03 01/02/14
Post a
Followup
You cannot reply to this message because you are not
logged in
.