Subject	No, I was doing the timing belt so
Posted by	Brad(RI) on January 01, 2014 at 1:53 PM
	This message has been viewed 268 times.
In Reply To	did you use a 5mm drill bit and drill it out with the motor posted by LJZTT on January 01, 2014 at 01:01 PM
Message	I pulled the manifold and removed the cam shaft. I asked around and couldn't find anyone who thought it would be a good idea to try to drill it in place. I think the OEM pin is case hardened which may explain why it goes quickly once it startes to wear. Once we center drilled it, it was pretty soft easily tapped.
Follow Ups	I am Spartacus - Brad(RI) 22:26:42 12/31/13 lol. Stay off the steroids. (n/m) - ForceFedTT (SoCal) 00:45:19 01/01/14 Do you have the new one installed? (n/m) - Alan (TN) 01:45:25 01/01/14 Yes, all installed - Brad(RI) 09:43:17 01/01/14 did you use a 5mm drill bit and drill it out with the motor - LJZTT 13:01:30 01/01/14 No, I was doing the timing belt so - Brad(RI) 13:53:21 01/01/14 there has got to be a good way to remove it w/out - LJZTT 20:21:47 01/01/14 You need to check the spline on your CAS. Worn spline - Alan (TN) 14:14:16 01/01/14 I checked it yes, it only has about 2,000 miles on it - Brad(RI) 14:48:32 01/01/14 ugh, I have to do this as well (n/m) - LJZTT 02:31:37 01/01/14 What material is this made from? - bartz32tt 10:08:52 01/01/14 The replacment is Chrome Moly - Brad(RI) 10:18:39 01/01/14 Sorry but I don't recognize this part - SammybTT(TN) 10:22:17 01/01/14 Here is a link that discusses this issue and the cure - Brad(RI) 10:42:18 01/01/14 I guess the photo threw me off - SammybTT(TN) 11:37:43 01/01/14 it doesn't have to get worn down exclusively for the reasons - LJZTT 12:40:21 01/01/14 The misalignment issues is theoretically limited to early - Brad(RI) 13:35:15 01/01/14 The grease is in there more to seal out moisture - ZXoltan 18:23:24 01/01/14 Is this only an issue on some z32's or all? (n/m) - VERTTZ 11:16:17 01/01/14 according to JWT early 90 models if it results from the - LJZTT 12:59:46 01/01/14 Ah. Well I just read that all of the JWT camshafts come with - VERTTZ 16:53:32 01/01/14 If your cam mount is misaligned you're likely to - ZXoltan 18:17:21 01/01/14 I would think you could still have this happen, but that - LJZTT 20:24:25 01/01/14 I had to replace the spline in a set of JWT cams. I believe - Alan (TN) 22:22:19 01/01/14 They don't unless its a newer change they made. - Woody75 (Denver) 10:30:54 01/02/14 Per JWT current web page, All billet cams come with the - Brad(RI) 18:21:03 01/02/14
Post a Followup	You cannot reply to this message because you are not logged in.