TwinTurbo.NET: Nissan 300ZX forum - Sorry but I don't recognize this part
Subject
Sorry but I don't recognize this part
Posted by
SammybTT(TN)
on January 01, 2014 at 10:22 AM
This message has been viewed
261
times.
In Reply To
I am Spartacus
posted by Brad(RI)
on December 31, 2013 at 10:26 PM
Message
I wish I could blame it on my phone screen. Lol
Please educate me. Thanks
Follow Ups
I am Spartacus
-
Brad(RI)
22:26:42 12/31/13
lol. Stay off the steroids. (n/m)
-
ForceFedTT (SoCal)
00:45:19 01/01/14
Do you have the new one installed? (n/m)
-
Alan (TN)
01:45:25 01/01/14
Yes, all installed
-
Brad(RI)
09:43:17 01/01/14
did you use a 5mm drill bit and drill it out with the motor
-
LJZTT
13:01:30 01/01/14
No, I was doing the timing belt so
-
Brad(RI)
13:53:21 01/01/14
there has got to be a good way to remove it w/out
-
LJZTT
20:21:47 01/01/14
You need to check the spline on your CAS. Worn spline
-
Alan (TN)
14:14:16 01/01/14
I checked it yes, it only has about 2,000 miles on it
-
Brad(RI)
14:48:32 01/01/14
ugh, I have to do this as well (n/m)
-
LJZTT
02:31:37 01/01/14
What material is this made from?
-
bartz32tt
10:08:52 01/01/14
The replacment is Chrome Moly
-
Brad(RI)
10:18:39 01/01/14
Sorry but I don't recognize this part -
SammybTT(TN)
10:22:17 01/01/14
Here is a link that discusses this issue and the cure
-
Brad(RI)
10:42:18 01/01/14
I guess the photo threw me off
-
SammybTT(TN)
11:37:43 01/01/14
it doesn't have to get worn down exclusively for the reasons
-
LJZTT
12:40:21 01/01/14
The misalignment issues is theoretically limited to early
-
Brad(RI)
13:35:15 01/01/14
The grease is in there more to seal out moisture
-
ZXoltan
18:23:24 01/01/14
Is this only an issue on some z32's or all? (n/m)
-
VERTTZ
11:16:17 01/01/14
according to JWT early 90 models if it results from the
-
LJZTT
12:59:46 01/01/14
Ah. Well I just read that all of the JWT camshafts come with
-
VERTTZ
16:53:32 01/01/14
If your cam mount is misaligned you're likely to
-
ZXoltan
18:17:21 01/01/14
I would think you could still have this happen, but that
-
LJZTT
20:24:25 01/01/14
I had to replace the spline in a set of JWT cams. I believe
-
Alan (TN)
22:22:19 01/01/14
They don't unless its a newer change they made.
-
Woody75 (Denver)
10:30:54 01/02/14
Per JWT current web page, All billet cams come with the
-
Brad(RI)
18:21:03 01/02/14
Post a
Followup
You cannot reply to this message because you are not
logged in
.