Subject	Re: I installed my rear crank sprocket washer backwards.
Posted by	blueridge on December 21, 2013 at 12:28 PM
	This message has been viewed 212 times.
In Reply To	I installed my rear crank sprocket washer backwards. posted by rojoloco (VA Beach) on December 20, 2013 at 09:16 AM
Message	Spent 3 months building my engine. Installed in car. Went to tighten crank pulley with socket extension through the pulley and cracked the oil pump when I tried to tighten it. I recieved the dumb award for the day. Blueridge
Follow Ups	Stupid things I do when working on a Z. - z32z 18:00:36 12/18/13 we've all done stupid stuff at one time or another, like.. - Stanky 19:42:55 12/18/13 I put teflon tape on new PCV vales so they would seal better - MrOzzie5183 20:37:16 12/18/13 oohh, that would make me so mad (n/m) - LJZTT 17:11:44 12/19/13 Forgot the boost leak tester - vorpalZ 21:18:48 12/18/13 Lol. Good times. (n/m) - MixManMash 07:17:38 12/19/13 Had fuel lines crisscrossed. Then forgot I had a towel over - LivinTheDream 09:28:30 12/19/13 I left a rag on top of the fan shroud once - -Grimm- 09:49:10 12/19/13 Didnt the Aux fan come on with key on and no ECU? (n/m) - BOOZTD 3 09:36:04 12/19/13 I stuck my thumb in the AUX fan once. It hurted. - Drk93TT 11:30:46 12/19/13 why? it wasn't your beerhand, you're good to go! (n/m) - LJZTT 17:09:59 12/19/13 There's been a couple but the latest was trying to - SammybTT(TN) 12:06:25 12/19/13 decided not to put front strut bar on after plenum pull - fuzzymonkey 12:20:21 12/19/13 Torquing 18 bolts in sequence for your OSG Twin Plate... - ZinnZ32 12:20:45 12/19/13 Let my lift down with car onto a brand newly installed koyo - KongZTT GT28RS MD 12:54:14 12/19/13 Installed my heads on backwards, yes it can be done. - ZaXxon 14:52:50 12/19/13 Finished assembling a motor and installed, loosened cas - Krazyd27(Houston) 18:31:30 12/19/13 left my radiator cap loose and shut my hood then drove off - Whip 17:02:40 12/19/13 installed my SPL coilovers, forgot to pre-adjust them for - LJZTT 17:08:49 12/19/13 Pulled the oil cooler to drain it - Broke_as_**** 00:09:50 12/20/13 R (n/m) - BoneZ (MD) 08:34:08 12/20/13 Dip stick left in when replacing oil pan gaskets. It only - CmyZ 08:34:29 12/20/13 Yup. I left the dipstick in while replacing an oil pan with - MixManMash 10:44:31 12/20/13 hey... you leave me out of this... let me admit my own - vorpalZ 23:33:45 12/20/13 I installed my rear crank sprocket washer backwards. - rojoloco (VA Beach) 09:16:57 12/20/13 Re: I installed my rear crank sprocket washer backwards. - blueridge 12:28:32 12/21/13
Post a Followup	You cannot reply to this message because you are not logged in.