Subject	Pulled the oil cooler to drain it
Posted by	Broke_as_**** on December 20, 2013 at 12:09 AM
	This message has been viewed 326 times.
In Reply To	Stupid things I do when working on a Z. posted by z32z on December 18, 2013 at 06:00 PM
Message	In amongst a few other things I do during an oil change. So while it was draining I figured I'd get ahead of the game and do a boost leak test. Which pressurizes the crank case. And subsequently the oil return line from the oil cooler. Which now has no oil cooler to stop it shooting oil across the garage. Made quite a mess.
Follow Ups	Stupid things I do when working on a Z. - z32z 18:00:36 12/18/13 we've all done stupid stuff at one time or another, like.. - Stanky 19:42:55 12/18/13 I put teflon tape on new PCV vales so they would seal better - MrOzzie5183 20:37:16 12/18/13 oohh, that would make me so mad (n/m) - LJZTT 17:11:44 12/19/13 Forgot the boost leak tester - vorpalZ 21:18:48 12/18/13 Lol. Good times. (n/m) - MixManMash 07:17:38 12/19/13 Had fuel lines crisscrossed. Then forgot I had a towel over - LivinTheDream 09:28:30 12/19/13 I left a rag on top of the fan shroud once - -Grimm- 09:49:10 12/19/13 Didnt the Aux fan come on with key on and no ECU? (n/m) - BOOZTD 3 09:36:04 12/19/13 I stuck my thumb in the AUX fan once. It hurted. - Drk93TT 11:30:46 12/19/13 why? it wasn't your beerhand, you're good to go! (n/m) - LJZTT 17:09:59 12/19/13 There's been a couple but the latest was trying to - SammybTT(TN) 12:06:25 12/19/13 decided not to put front strut bar on after plenum pull - fuzzymonkey 12:20:21 12/19/13 Torquing 18 bolts in sequence for your OSG Twin Plate... - ZinnZ32 12:20:45 12/19/13 Let my lift down with car onto a brand newly installed koyo - KongZTT GT28RS MD 12:54:14 12/19/13 Installed my heads on backwards, yes it can be done. - ZaXxon 14:52:50 12/19/13 Finished assembling a motor and installed, loosened cas - Krazyd27(Houston) 18:31:30 12/19/13 left my radiator cap loose and shut my hood then drove off - Whip 17:02:40 12/19/13 installed my SPL coilovers, forgot to pre-adjust them for - LJZTT 17:08:49 12/19/13 Pulled the oil cooler to drain it - Broke_as_**** 00:09:50 12/20/13 R (n/m) - BoneZ (MD) 08:34:08 12/20/13 Dip stick left in when replacing oil pan gaskets. It only - CmyZ 08:34:29 12/20/13 Yup. I left the dipstick in while replacing an oil pan with - MixManMash 10:44:31 12/20/13 hey... you leave me out of this... let me admit my own - vorpalZ 23:33:45 12/20/13 I installed my rear crank sprocket washer backwards. - rojoloco (VA Beach) 09:16:57 12/20/13 Re: I installed my rear crank sprocket washer backwards. - blueridge 12:28:32 12/21/13
Post a Followup	You cannot reply to this message because you are not logged in.