Subject	Forgot to mention
Posted by	-Grimm- on August 21, 2013 at 10:42 AM
	This message has been viewed 256 times.
In Reply To	Personal Opinions on Compression Situation posted by 300ZMang on August 21, 2013 at 09:48 AM
Message	While the engine is out (assuming you don't want to pull the heads in the car, which I've done and would not suggest) I would also hone your cylinders and replace the rings and bearings. Its only a couple hundred more.
Follow Ups	Personal Opinions on Compression Situation - 300ZMang 09:48:20 08/21/13 Find a good used TT engine and swap it in. - MixManMash 09:58:45 08/21/13 Have your heads repaired - -Grimm- 10:40:52 08/21/13 Forgot to mention - -Grimm- 10:42:01 08/21/13 I located a used TT engine for a fair price, so I'm not - 300ZMang 10:49:17 08/21/13 In total... - -Grimm- 16:57:43 08/21/13 and cost for valves right? (n/m) - 300ZMang 17:13:45 08/21/13 From what I understand - -Grimm- 09:19:10 08/22/13 least painful way out is good used engine. - Antihero 11:12:38 08/21/13 I think anyone can tear an engine apart - 300ZMang 11:27:33 08/21/13 how many VG heads have they done? - LJZTT 15:28:38 08/21/13 they r the one shop everyone uses - 300ZMang 17:15:14 08/21/13 "everyone" goes to walmart too (n/m) - LJZTT 18:13:27 08/21/13 That made no sense, any REAL input? Didn't think so (n/m) - 300ZMang 08:04:18 08/22/13 not my fault you're dumb as a rock (n/m) - LJZTT 20:43:45 08/22/13 Option 3. Good luck (n/m) - Nate (NoVA) 11:16:50 08/21/13 Was that sarcasm? Couldn't tell, if not, thanks! ha (n/m) - 300ZMang 11:24:44 08/21/13 nope. (n/m) - Nate (NoVA) 12:11:24 08/21/13 If you walked into my shop with this problem I would - TTZ2NV(EPTmotorsports) 11:56:52 08/21/13 Very good info though, thank you! - 300ZMang 12:08:57 08/21/13 Nobody is going to warranty new parts on their old engine - ZXoltan 16:48:04 08/21/13 Agreed. (n/m) - ConVerTT 19:28:18 08/21/13 option 1 or 2. why would you put an engine that you have no - toykoz32 12:19:21 08/21/13 What did the rebuilds cost you? - 300ZMang 12:27:49 08/21/13 short block rebuild is 750 and heads are 300 (n/m) - toykoz32 12:49:59 08/21/13 Who did the block rebuild so cheap and what did they do? - ZXoltan 15:03:04 08/21/13 thats the price for a stock rebuild with bearings and rings (n/m) - toykoz32 19:55:21 08/21/13 Remove the heads, put a live grenade in cylinder 1, then - ForceFedTT (SoCal) 23:39:36 08/21/13 I'd rather not, bc cylinder 1 is still good. - 300ZMang 08:05:26 08/22/13 yeah, driver seat is a good call. you would have to call it - ForceFedTT (SoCal) 16:13:39 08/23/13
Post a Followup	You cannot reply to this message because you are not logged in.