Subject	Find a good used TT engine and swap it in.
Posted by	MixManMash on August 21, 2013 at 9:58 AM
	This message has been viewed 205 times.
In Reply To	Personal Opinions on Compression Situation posted by 300ZMang on August 21, 2013 at 09:48 AM
Message	That will probably be your best bet. Make sure you can get compression & leakdown numbers on the used TT engine. Still, be prepared to spend some money on the used engine to redo timing belt, water pump, seals, gaskets, etc.
Follow Ups	Personal Opinions on Compression Situation - 300ZMang 09:48:20 08/21/13 Find a good used TT engine and swap it in. - MixManMash 09:58:45 08/21/13 Have your heads repaired - -Grimm- 10:40:52 08/21/13 Forgot to mention - -Grimm- 10:42:01 08/21/13 I located a used TT engine for a fair price, so I'm not - 300ZMang 10:49:17 08/21/13 In total... - -Grimm- 16:57:43 08/21/13 and cost for valves right? (n/m) - 300ZMang 17:13:45 08/21/13 From what I understand - -Grimm- 09:19:10 08/22/13 least painful way out is good used engine. - Antihero 11:12:38 08/21/13 I think anyone can tear an engine apart - 300ZMang 11:27:33 08/21/13 how many VG heads have they done? - LJZTT 15:28:38 08/21/13 they r the one shop everyone uses - 300ZMang 17:15:14 08/21/13 "everyone" goes to walmart too (n/m) - LJZTT 18:13:27 08/21/13 That made no sense, any REAL input? Didn't think so (n/m) - 300ZMang 08:04:18 08/22/13 not my fault you're dumb as a rock (n/m) - LJZTT 20:43:45 08/22/13 Option 3. Good luck (n/m) - Nate (NoVA) 11:16:50 08/21/13 Was that sarcasm? Couldn't tell, if not, thanks! ha (n/m) - 300ZMang 11:24:44 08/21/13 nope. (n/m) - Nate (NoVA) 12:11:24 08/21/13 If you walked into my shop with this problem I would - TTZ2NV(EPTmotorsports) 11:56:52 08/21/13 Very good info though, thank you! - 300ZMang 12:08:57 08/21/13 Nobody is going to warranty new parts on their old engine - ZXoltan 16:48:04 08/21/13 Agreed. (n/m) - ConVerTT 19:28:18 08/21/13 option 1 or 2. why would you put an engine that you have no - toykoz32 12:19:21 08/21/13 What did the rebuilds cost you? - 300ZMang 12:27:49 08/21/13 short block rebuild is 750 and heads are 300 (n/m) - toykoz32 12:49:59 08/21/13 Who did the block rebuild so cheap and what did they do? - ZXoltan 15:03:04 08/21/13 thats the price for a stock rebuild with bearings and rings (n/m) - toykoz32 19:55:21 08/21/13 Remove the heads, put a live grenade in cylinder 1, then - ForceFedTT (SoCal) 23:39:36 08/21/13 I'd rather not, bc cylinder 1 is still good. - 300ZMang 08:05:26 08/22/13 yeah, driver seat is a good call. you would have to call it - ForceFedTT (SoCal) 16:13:39 08/23/13
Post a Followup	You cannot reply to this message because you are not logged in.