Subject	haha you said eh.
Posted by	fuzzymonkey on July 09, 2013 at 3:50 AM
	This message has been viewed 206 times.
In Reply To	damn thats rough! nice to do yourself eh? (n/m) posted by 300ZMang on July 08, 2013 at 09:00 PM
Message	Seriously, start it off yourself! If you can't get everything back together, you've done half the job so labour has just been cut in half of paying someone. -remove exhaust -remove driveshaft -remove starter -remove shifter linkage -remove all bolts on bell housing you can see -remove tranny mount and place jack under tranny -lower back side of tranny -remove top two bell housing bolts -pull transmission off -undo pressure plate (9 bolts iirc) -remove clutch, remove flywheel (like 9 bolts too) -get flywheel machined -reverse steps I'm sure you can do 90% of it. The other 10% you're just afraid to do. Throw those fears away. If you do it, i'll call in and buy you a delivered pizza. Hawaiian.
Follow Ups	Beer, Pizza & Money - 300ZMang 09:53:26 07/08/13 Ship it to Vancouver and i'll do it for just pizza - fuzzymonkey 13:56:34 07/08/13 Re: Ship it to Vancouver and i'll do it for just pizza - elcid 14:10:27 07/08/13 I called you last week when I was in Abby - fuzzymonkey 15:46:34 07/08/13 Try it yourself! Really not too hard! - PYROhafe 16:03:08 07/08/13 appreciate it man! - 300ZMang 21:15:53 07/08/13 Re: appreciate it man! - PYROhafe 16:12:37 07/09/13 Trust me - 300ZMang 07:13:00 07/10/13 Well too bad I'm not closer to Vancouver - 300ZMang 15:21:02 07/08/13 fuzzymonkey is a Stage V addict: Changes clutches on Zs just - fuzzymonkey 15:54:21 07/08/13 Yup R&R takes me and a buddy about 5 hours. It helps having - MixManMash 17:06:37 07/08/13 and that included a drive over to the shop to show - vorpalZ 17:25:33 07/08/13 Yup. You back yet? (n/m) - MixManMash 17:29:02 07/08/13 Sitting in the club lounge at Calgary... board at 6 (n/m) - vorpalZ 17:50:20 07/08/13 I have forgotten the shield way too many times. - fuzzymonkey 18:42:30 07/08/13 Some people can fuck up a cup of coffee.... - Schmeal (NV) 19:09:51 07/08/13 damn thats rough! nice to do yourself eh? (n/m) - 300ZMang 21:00:01 07/08/13 You just have to take your time and be thorough. (n/m) - Schmeal (NV) 01:40:49 07/09/13 haha you said eh. - fuzzymonkey 03:50:30 07/09/13 Here ya go... - spicyZ 16:00:23 07/08/13 you have more confidence in me than I do haha (n/m) - 300ZMang 21:12:49 07/08/13 Can you remove bolts and screw them back in? - spicyZ 08:37:52 07/09/13 I got tired of getting bent over. - PCVI 10:33:18 07/09/13 Yes, I'm attempting to refrain from being bent over - 300ZMang 11:04:37 07/09/13 Re: Yes, I'm attempting to refrain from being bent over - PCVI 13:00:14 07/09/13 I hear ya, loud and clear - 300ZMang 14:27:25 07/09/13 If you need a garage to do the work - BondzTT 13:07:00 07/09/13 You've got mail (n/m) - 300ZMang 13:49:33 07/09/13 Im a Nissan dealer in Middlebury, can hook you up with parts - BannonZ 11:25:39 07/09/13 Contact member Turbodog (CT) - BigTDogg (MA) 14:19:14 07/09/13 Thanks Tony... I know I've emailed him before - 300ZMang 14:28:45 07/09/13 Encountered some hiccups, working out the kinks :) (n/m) - BigTDogg (MA) 14:39:20 07/09/13
Post a Followup	You cannot reply to this message because you are not logged in.