Subject	I agree on drivability, sort of ....
Posted by	ConVerTT on July 01, 2013 at 1:30 PM
	This message has been viewed 234 times.
In Reply To	I know others have their opinion, but mine is that for what posted by Ash's Z on June 29, 2013 at 06:26 PM
Message	My SlickTTop (500 rwhp on pump, 60 mm Altima TBs) has a very binary feel. By that I mean it is less progressive, more on/off relative to stock TBs. Whether that is good or bad is subjective and situational - sometimes I like it, sometimes not. I've had both (stock and 60s) on my pearl VerTT. (Both times tuned by SZ). I doubt that they add any horsepower whatsoever.
Follow Ups	? bored throttle body worth any power ? -- data - shaggee 13:57:17 06/29/13 RE: stock 50mm vs 58mm Z1 TB (search before buying these) - 240Z FeO2 16:36:05 06/29/13 I know others have their opinion, but mine is that for what - Ash's Z 18:26:29 06/29/13 Can you elaborate on "suck to drive?" - Jkova300z 19:02:12 06/29/13 The suck to drive is because you lose resolution down low - BlackholeZ 19:38:04 06/29/13 My Z1 TB's feel a bit sticky. - SimaYi 19:12:22 06/29/13 Mine were fine after new bore and plates... (n/m) - Z ONLY1 20:26:56 06/29/13 So you think with 2.5" charge piping, they're still not - BigTDogg (MA) 21:47:11 06/29/13 "super-marginal" = oxymoron (n/m) - lil'abner 14:23:31 06/30/13 What a ridiculously sensible observation! =) (n/m) - Ash's Z 11:38:30 07/01/13 Whoa.. you bought a new Z? (n/m) - spicyZ 08:36:57 07/02/13 I agree on drivability, sort of .... - ConVerTT 13:30:05 07/01/13 Long story short is they aren't worth it. (n/m) - Evan(CA) 18:46:57 06/29/13 lol, if anyone should know, it's you, besides Ash of course. (n/m) - DVDBURN (MD) 09:07:01 06/30/13 You're probably thinking of a different Evan but that - Evan(CA) 15:46:11 06/30/13 I thought "breather mods" included inlets, outlets, charge - LJZTT 17:20:58 06/30/13 "Breather mods" has become some what of an ambiguous term. - Evan(CA) 22:52:26 06/30/13 I see - LJZTT 00:08:28 07/01/13 If you asked 5 different people you'd probably get 5 - Evan(CA) 01:16:27 07/01/13 What can be done to the heads apart from a valve job? - LivinTheDream 21:54:32 06/30/13 I'm no expert just an enthusiast who's been around a long - Evan(CA) 22:54:26 06/30/13 porting, cams..maybe .5mm oversize valves. (n/m) - Antihero 15:35:25 07/02/13 60mm stanzas, PITA for everyone involved in making them fit - maglito 20:48:36 06/30/13 Do you know what I have to say about that? - Josher 21:54:19 06/30/13 Thanks! (n/m) - maglito 23:00:49 06/30/13
Post a Followup	You cannot reply to this message because you are not logged in.