Subject	RE: stock 50mm vs 58mm Z1 TB (search before buying these)
Posted by	240Z FeO2 on June 29, 2013 at 4:36 PM
	This message has been viewed 417 times.
In Reply To	? bored throttle body worth any power ? -- data posted by shaggee on June 29, 2013 at 01:57 PM
Message	this from SZ: "We've gained almost 100 lb\ft of torque by adding these along with the Ash Massives\2.5" piping on a GT28RS equipped Z32." https://specialtyz.com/shop/300zx/z1-throttle-bodies.html You might want to call Greg or Seb and discuss how increasing TB diameter would benefit your particular setup. However, maximizing the gain achieved by increasing TB diameter has to be seen as one part of a "flowing more air" strategy that starts at the air filter and ends at the exhaust tip-->dual intake, larger dia. suction pipes, ICs, LD charge pipes; improved manis, larger DPs and LD exhaust pipes. Chance favors the informed
Follow Ups	? bored throttle body worth any power ? -- data - shaggee 13:57:17 06/29/13 RE: stock 50mm vs 58mm Z1 TB (search before buying these) - 240Z FeO2 16:36:05 06/29/13 I know others have their opinion, but mine is that for what - Ash's Z 18:26:29 06/29/13 Can you elaborate on "suck to drive?" - Jkova300z 19:02:12 06/29/13 The suck to drive is because you lose resolution down low - BlackholeZ 19:38:04 06/29/13 My Z1 TB's feel a bit sticky. - SimaYi 19:12:22 06/29/13 Mine were fine after new bore and plates... (n/m) - Z ONLY1 20:26:56 06/29/13 So you think with 2.5" charge piping, they're still not - BigTDogg (MA) 21:47:11 06/29/13 "super-marginal" = oxymoron (n/m) - lil'abner 14:23:31 06/30/13 What a ridiculously sensible observation! =) (n/m) - Ash's Z 11:38:30 07/01/13 Whoa.. you bought a new Z? (n/m) - spicyZ 08:36:57 07/02/13 I agree on drivability, sort of .... - ConVerTT 13:30:05 07/01/13 Long story short is they aren't worth it. (n/m) - Evan(CA) 18:46:57 06/29/13 lol, if anyone should know, it's you, besides Ash of course. (n/m) - DVDBURN (MD) 09:07:01 06/30/13 You're probably thinking of a different Evan but that - Evan(CA) 15:46:11 06/30/13 I thought "breather mods" included inlets, outlets, charge - LJZTT 17:20:58 06/30/13 "Breather mods" has become some what of an ambiguous term. - Evan(CA) 22:52:26 06/30/13 I see - LJZTT 00:08:28 07/01/13 If you asked 5 different people you'd probably get 5 - Evan(CA) 01:16:27 07/01/13 What can be done to the heads apart from a valve job? - LivinTheDream 21:54:32 06/30/13 I'm no expert just an enthusiast who's been around a long - Evan(CA) 22:54:26 06/30/13 porting, cams..maybe .5mm oversize valves. (n/m) - Antihero 15:35:25 07/02/13 60mm stanzas, PITA for everyone involved in making them fit - maglito 20:48:36 06/30/13 Do you know what I have to say about that? - Josher 21:54:19 06/30/13 Thanks! (n/m) - maglito 23:00:49 06/30/13
Post a Followup	You cannot reply to this message because you are not logged in.