Subject	New numbers with breather mods
Posted by	nmgoodthing on May 21, 2013 at 10:11 AM
	This message has been viewed 948 times.
Message	I know I haven't updated my profile and apologize. I did the 2.5 piping throughout, Z1 58mm TBs, Z1 BA Intercoolers. Car has Z1 GT725s with ID 1000's, Winfuel top feed running e70 running 24psi. Tuned with Nistune. We couldn't get clean pulls in third due to the car breaking traction on the dyno. We tried fourth gear pulls with 2 people in the back and still spun. I was hoping to turn it up a bit, but the car is a beast and has a lot more left. I gained 38footlbs with the piping that we can actually see. I'd liek to thank Alex at NM Imports for making this happen, CAMTuning for the tune, and Mitch at EP racing for the bad ass oil pan and new oil set up. Because street car!
Follow Ups	New numbers with breather mods - nmgoodthing 10:11:02 05/21/13 very sick! - Red Hawk (CO) 10:25:47 05/21/13 Dyno rollers where a bit worn - nmgoodthing 10:28:00 05/21/13 Nice numbers - megaDan 10:31:08 05/21/13 Very nice. Do you have any pics / details of the oil pan ? (n/m) - z32z 10:34:10 05/21/13 I have some pics somewhere - nmgoodthing 10:46:42 05/21/13 are you doing a lot of track days? Competition rubber? - LJZTT 10:57:14 05/21/13 Re: are you doing a lot of track days? Competition rubber? - 1nostyZ 11:02:20 05/21/13 It sees the drag strip, street action... - nmgoodthing 11:47:10 05/21/13 I mean what prompted springing for the oil pan? - LJZTT 12:09:11 05/21/13 FWIW, my stock oil pan let me down on the track as well - ZinnZ32 13:12:47 05/21/13 How long did you get away with it? Did you gradually mod - LJZTT 15:12:36 05/21/13 Fully built motor all at once. Tuned appropriately etc. - ZinnZ32 15:36:01 05/21/13 My last motor I spun a bearing.. - nmgoodthing 13:48:56 05/21/13 Well in Nissan's defense, they didnt equip the car for any - LJZTT 15:02:19 05/21/13 no kidding. Even with stock size brembos - Red Hawk (CO) 15:15:38 05/21/13 The Z's braking performance was great in 1989. - Antihero 15:56:51 05/21/13 repeated hard trials can mean anything - LJZTT 16:24:58 05/21/13 you misunderstand... - Antihero 12:55:58 05/22/13 I've kind of been wishing for an inbetween - BlackholeZ 01:32:05 05/22/13 Re: I have some pics somewhere - Tech@EPR 12:41:09 05/21/13 where do most people mount their remote oil filter? (n/m) - aliaZ 06:18:29 05/22/13 Re: where do most people mount their remote oil filter? - Tech@EPR 09:51:53 05/22/13 Well your car is kinda fast, huh? (n/m) - 300ZMang 11:32:40 05/21/13 Looks like the VTC system is not working..... - Greg D. (Specialty-Z) 11:55:21 05/21/13 I'm not sure Greg, I'll - nmgoodthing 12:00:55 05/21/13 Let me know if the check valves were installed - Greg D. (Specialty-Z) 12:44:23 05/21/13 Kindof typical of the Z1725 turbos though... GT2871s - Ash's Z 12:42:53 05/21/13 I dis-agree, the 2871 are laggy for sure, but with working - Greg D. (Specialty-Z) 13:03:33 05/21/13 Re: Looks like the VTC system is not working..... - 1nostyZ 12:45:25 05/21/13 The chart is classic of non working VTC IMO..... - Greg D. (Specialty-Z) 13:08:33 05/21/13 It can't hurt to check it - nmgoodthing 13:57:03 05/21/13 Easiest thing to do is turn the VTC solenoids on at idle and - Ash's Z 15:08:03 05/21/13 any MT trans options when you get to this power level? - rmp459 12:05:22 05/21/13 I would like to know as well. - nmgoodthing 12:37:04 05/21/13 Why is that? (n/m) - SimaYi 14:15:34 05/21/13 Impressive results - RobZ32 13:06:49 05/21/13 I can't find last years dyno sheet :-( - nmgoodthing 13:55:01 05/21/13 Curious - How do you like the oil pan??? Good fitment? - ZinnZ32 13:09:09 05/21/13 It's big, it's huge, it's tight... but - nmgoodthing 13:42:12 05/21/13 pan doesn't sit any lower relative to the crossmember - aliaZ 06:20:14 05/22/13 Re: New numbers with breather mods - BLACKBEAST 06:13:21 05/22/13
Post a Followup	You cannot reply to this message because you are not logged in.