Subject	You're correct on the lower compression with aggressive
Posted by	PiotrC70 on April 22, 2013 at 9:32 PM
	This message has been viewed 188 times.
In Reply To	Mods are the same except the long block posted by MeatMan - 604Z.ca - on April 22, 2013 at 10:02 AM
Message	cams... thought it was weird until I asked... makes sense though. Due to the low miles I drive per year 2-3k at best, I talked to Kyle about the hard break in and went that route since it would take me a year to break it in the traditional way. After about 200 miles on the motor, I had about 115-117 across the board using conventional 10w-30 using a harbor freight compression tester since the other one we were using read high. After about 2000 miles on the build and a little more than 100 miles or so after switching to Mobil1 0w-40 and buying a new compression tester(OTC), I checked values compared to my air compressor regulator at different values, I had 141-146 across the board. 1993 TT. R.I.P. 09.15.2010
Follow Ups	Thoughts on this idle issue - MeatMan - 604Z.ca - 01:27:45 04/22/13 I would say that looks a bit like a small vac leak - Medallion Man 02:47:44 04/22/13 Throttle bodies were balanced by Greg when he was here, - MeatMan - 604Z.ca - 10:09:53 04/22/13 IIRC mine wandered like that when my throttle cables were - LJZTT 04:08:40 04/22/13 I will check the tension to ensure there is no issue there.. - MeatMan - 604Z.ca - 10:05:27 04/22/13 Re: I will check the tension to ensure there is no issue there.. - Huber300zx 14:29:34 04/22/13 Your idle AFR is rich, should be more like your cruise AFR - ttsmokin 16:22:29 04/22/13 It is dyno tuned, and my old engine was set with datascan... - MeatMan - 604Z.ca - 17:07:32 04/22/13 Sorry Josh, was talking to Huber300zx (n/m) - ttsmokin 23:34:19 04/22/13 update your profile(use firefox or chrome).... - PiotrC70 21:38:51 04/22/13 I'm assuming the mods are not the same as in your profile - i_s_64 04:41:41 04/22/13 Mods are the same except the long block - MeatMan - 604Z.ca - 10:02:46 04/22/13 But was it degree'd with adjustable camshaft gears? - i_s_64 10:16:58 04/22/13 You're correct on the lower compression with aggressive - PiotrC70 21:32:13 04/22/13 I have 500 cams. My idle is steady. Only issue that I have - MixManMash 08:23:57 04/22/13 Are you positive that your AAC solenoid is functioning? - Evan_Wright (Ca) 10:30:35 04/22/13 Pretty sure. Fairly new unit and I can vary the duty cycle - MixManMash 11:03:47 04/22/13 Yeah, sounds like your AAC is working fine :) - Evan_Wright (Ca) 11:07:40 04/22/13 whats the suspected part ordered? ;) (n/m) - samsung-Z [Houston] 13:17:08 04/22/13 Me 3! I Have 500 cams, SAME issue - VERTTZ 18:18:21 04/22/13 are your mafs experiencing turbulence from direct airflow - samsung-Z [Houston] 19:54:44 04/22/13 Possibly. But I have ruled that out... - VERTTZ 02:14:10 04/23/13 After talking with Greg, I understand now how to properly - PiotrC70 21:23:08 04/22/13
Post a Followup	You cannot reply to this message because you are not logged in.