Subject	You are right to refer to Kyle's list, if you insist on not
Posted by	zellamay on April 04, 2013 at 3:05 PM
	This message has been viewed 297 times.
In Reply To	So how would you build a motor? posted by BlackholeZ on April 04, 2013 at 03:48 AM
Message	having him build it for you. True, stock pistons are good enough, so why does he use Weisco? Ask him. Of course, many other people know engines, but he has the best rep around, so when getting 2 different opinions, I'd go with his. He makes no mention of knifing cranks. He expands water passages, even on his most basic build. I know he offers the piston coating, not sure what else.
Follow Ups	So how would you build a motor? - BlackholeZ 03:48:51 04/04/13 "Hey Kyle, can you build me this motor?" - Adam (NoVA) 07:40:06 04/04/13 "You down with IPP?" "Yeah, you know me!" (n/m) - Nate (NoVA) 08:41:46 04/04/13 "Naughty by Nature, not cause I hate ya." (n/m) - MixManMash 12:17:25 04/04/13 I wouldnt go through IPP - Zsgetyoulaid 09:08:27 04/05/13 Sorry to hear you had a bad experience. Numerous members on - MixManMash 10:56:00 04/05/13 Completely agree - Zsgetyoulaid 11:00:57 04/05/13 Just for the record - Kyle(Houston) 13:08:13 04/05/13 Re: Just for the record - Zsgetyoulaid 13:36:44 04/05/13 That's a lot of if's and could's. (n/m) - Adam (NoVA) 16:15:23 04/06/13 The ambiguity was intentional (n/m) - Zsgetyoulaid 13:18:09 04/07/13 stage IV or V imo (n/m) - genic 19:57:02 04/04/13 knife edging the crank is not so simple - FuerGrissa 09:38:17 04/04/13 The wiseco pistons are forged, stock is casted - Zvil (FL) 10:21:15 04/04/13 Some good points, thanks - BlackholeZ 11:21:33 04/04/13 Also I am pretty sure only the bearing surfaces get nitrided - BlackholeZ 11:26:03 04/04/13 Actually thats not quite how forged pistons are manufactured - ZXoltan 15:30:21 04/04/13 To be honest I'll admit I meant forged starts out casted - Zvil (FL) 16:26:08 04/04/13 you're right about that but all the non-bearing surfaces - Zvil (FL) 16:28:02 04/04/13 Yeah I think you're right (n/m) - BlackholeZ 17:49:44 04/04/13 the whole crank gets nitrided, not just the journals (n/m) - aliaZ 18:42:44 04/04/13 You are right to refer to Kyle's list, if you insist on not - zellamay 15:05:02 04/04/13 Does anyone have documentation on the cranks being nitrided? - BlackholeZ 17:50:49 04/04/13 They are probably used to building american engines (n/m) - ttsmokin 12:56:29 04/05/13 He was comparing it to other cranks that are nitrided - BlackholeZ 15:51:57 04/05/13 there are several different processes for nitriding - aliaZ 07:48:05 04/06/13 tell your builder to go eff himself (n/m) - aliaZ 13:08:02 04/05/13
Post a Followup	You cannot reply to this message because you are not logged in.