Subject	I took mine to the local speed shop.
Posted by	SammybTT(TN) on March 06, 2013 at 12:46 PM
	This message has been viewed 200 times.
In Reply To	To the people that have built their motor posted by Nis300owner on March 06, 2013 at 10:25 AM
Message	I am pretty sure that they didn't use a torque plate. I selected them from some engine work they did before on my boat. Looking back I am not sure if I would use them again since they had changed owners but at the time there is not much of a choice in my area without a long drive. I went with a basic low end rebuild 500hp so this wasn't a major concern. Good luck and keep us posted.
Follow Ups	To the people that have built their motor - Nis300owner 10:25:45 03/06/13 To do it right the first time. - Tanley 12:10:23 03/06/13 This is the correct answer as far as I'm concerned..... (n/m) - Gold Z 12:17:34 03/06/13 Sure it would be but what would I learn from that - Nis300owner 12:30:23 03/06/13 Same boat here, I love the assembly part, but I would like - puddlejumpinzx 13:22:44 03/06/13 Haha no problem we all have to help eachother out. - Nis300owner 00:10:39 03/07/13 This may sounds stupid but... - Red Hawk (CO) 14:21:11 03/06/13 Speaking from someone whos been down your road... - white22sky 12:48:52 03/06/13 Never done a Z motor for one and two I like to look - Nis300owner 00:06:55 03/07/13 Fair enough, I can appreciate that. - white22sky 12:24:41 03/07/13 I took mine to the local speed shop. - SammybTT(TN) 12:46:37 03/06/13 Yea that makes sense. Thanks (n/m) - Nis300owner 16:58:48 03/06/13 Check with Opel engineering in Schaumburg. - spdrmn15 13:05:45 03/06/13 Perfect thank you! That's what I'm looking for (n/m) - Nis300owner 16:55:17 03/06/13 Kyle with IPP will answer all your questions and the savings - Xteam300TT (South Tx ) 14:07:11 03/06/13 Yea will definitely be getting to know Kyle with - Nis300owner 00:09:01 03/07/13 call Kyle and stop there. no issues going forward (n/m) - The Devils Z 10:16:58 03/07/13 I used a torque plate and multiposition bore measurement - Jim (Selin Design) 15:00:41 03/06/13 Exactly what I've been reading! Thanks for - Nis300owner 17:02:00 03/06/13 I have a torque plate - ZXoltan 15:54:14 03/06/13 Interested if the shop I choose doesn't have one. - Nis300owner 16:59:49 03/06/13 Re: I have a torque plate - wild_maxx 05:21:10 03/07/13 Re: I have a torque plate - wild_maxx 11:48:59 03/07/13 Go to Opel in Streamwood IL - c300zxtt (Chi) 17:01:56 03/06/13 Now that is really interesting. Definitely will be talking - Nis300owner 17:04:49 03/06/13 I look for a nice cylinder hone - aliaZ 06:29:59 03/07/13 Re: I look for a nice cylinder hone - JSD-ZX 10:41:55 03/07/13
Post a Followup	You cannot reply to this message because you are not logged in.