Subject	You can use the stock wires with with one condition you must
Posted by	Spectrum (WI) on February 17, 2013 at 10:52 AM
	This message has been viewed 163 times.
In Reply To	Installing new stereo, should I run new wires? posted by elcid on February 16, 2013 at 04:17 PM
Message	disconnect those Bose amps inside each speaker and run a jumper wire directly to the speakers. Unfortunately you have to remove the door panel and access the speakers. Sometimes those factory Bose amps don't like to receive an amplified signal from an aftermarket stereo. A way around this is to make a little jumper harness. Splice some wires from outside the Bose enclosure, disassemble the factory Bose speaker enclosure and unplug that little amp. Drill a small hole for your wires and plug them in directly to the speaker effectively bypassing the factory amps.
Follow Ups	Installing new stereo, should I run new wires? - elcid 16:17:07 02/16/13 I did, I must warn you it a PITA!!! (n/m) - Zski 16:46:20 02/16/13 i installed new wiring when i installed my amplifier to.. - DJ2_300zxLover 16:50:15 02/16/13 I like to use xmas tree lights for the wires, this way I get - ForceFedTT (SoCal) 17:22:33 02/16/13 I laughed my ass off at the the xmas tree wires... - nonstopna 23:46:34 02/16/13 :) (n/m) - ForceFedTT (SoCal) 00:14:10 02/17/13 Why run new wires? Just use the stock (n/m) - moxie (SF) 18:10:56 02/16/13 Re: Why run new wires? Just use the stock - elcid 18:35:37 02/16/13 no, dont cut them. Spend the $20 or so to buy - moxie (SF) 19:01:42 02/16/13 Makes no sense unless hooking up an amp (n/m) - LivinTheDream 18:21:50 02/16/13 Re: Makes no sense unless hooking up an amp - elcid 18:37:03 02/16/13 Re: Installing new stereo, should I run new wires? - ThunderZ 18:42:05 02/16/13 I'm doing the same - russ29 19:19:37 02/16/13 not the worst thing in the world. Does take time and you - LivinTheDream 22:56:02 02/16/13 ummm? What harness do we need? (n/m) - russ29 06:12:42 02/17/13 I believe they are referring to 'smart harnesses' - Burton(PA/FL) 07:24:36 02/17/13 Unless you're installing a 4-channel Amp - Burton(PA/FL) 07:21:14 02/17/13 Stereo shop will have a Nissan specific harness adapter - vorpalZ 09:04:56 02/17/13 Meh. New wires and "gordo faq treatment" on the doors while - ConVerTT 09:09:53 02/17/13 You can use the stock wires with with one condition you must - Spectrum (WI) 10:52:49 02/17/13 Do you have a Bose system? Or did you replace the speakers - BigTDogg (MA) 12:40:25 02/17/13 Re: Do you have a Bose system? Or did you replace the speakers - elcid 15:39:56 02/17/13 Here's some wiring help for that project. - DVDBURN (MD) 14:23:38 02/17/13 Re: Here's some wiring help for that project. - elcid 15:38:00 02/17/13 The jumpers allow the connection of the speakers - DVDBURN (MD) 17:27:59 02/17/13 1990 Bose amps are hard wired - ZXoltan 16:04:48 02/17/13 90 w. center speakers vs. 91+ - Bernie (NoVA) 16:15:38 02/17/13 Now that you mention it I do remember having to - DVDBURN (MD) 17:36:23 02/17/13 Could also just cut the amps out if you're not selling them (n/m) - BigTDogg (MA) 19:48:44 02/17/13 Is there a market for them? I have 3 good ones with speakers (n/m) - Jayru 21:47:42 02/17/13 If they work post them up in classifieds. If they're 1990s - BigTDogg (MA) 20:03:48 02/18/13
Post a Followup	You cannot reply to this message because you are not logged in.