Subject	Love the collars although i got urethane collars (easier on
Posted by	RonZ300 (Socal) on January 18, 2013 at 8:23 PM
	This message has been viewed 242 times.
In Reply To	While we're on the subject posted by Evan(CA) on January 18, 2013 at 07:56 PM
Message	the stock rubber and maybe slightly less noise transmitted) The urethane also dont have the gap because they are somewhat flexible (you wont have to drop the entire subframe, just lower it a bit) [ http://www.frsport.com/Peak-Performance-Polyurethane-Subframe-Spacer-Bushings-Nissan-S13-S14_p_1357.html ] Be careful with the SZ spacers as they raise the subframe up which also alters squat/anti-squat geometry.
Follow Ups	Compared to stock suspension... - Jiro 18:38:01 01/18/13 currently experiencing pretty bad wheel hop with this build. (n/m) - Jiro 18:39:01 01/18/13 Combined, about the same effect as subframe collars - TriniTT 19:23:01 01/18/13 The 300 degree kit wont be able to compensate for that much - Evan(CA) 19:52:08 01/18/13 alright subframe collars added to list. (n/m) - Jiro 20:51:50 01/18/13 While we're on the subject - Evan(CA) 19:56:22 01/18/13 Love the collars although i got urethane collars (easier on - RonZ300 (Socal) 20:23:45 01/18/13 They perform the same function, which is to preload the - TriniTT 13:09:22 01/19/13 FWIW I installed diff & subframe bushings and it helped - BlackholeZ 20:34:16 01/18/13 Have you checked the toe arm (HICAS) ball joints? - AHos(Chicago) 21:28:04 01/18/13 i have 2 replacement HICAS ball joints too some play there. (n/m) - Jiro 02:32:47 01/19/13 What are the spring rates for your coilovers? (n/m) - Gordo 93TT Daytona 21:48:55 01/18/13 You will also need... - hunterg 23:47:05 01/18/13 did you replace rear diff mount bushings too? (n/m) - Jiro 00:31:05 01/19/13 Starting from scratch again...Updated list suspension: - Jiro 01:09:00 01/19/13 I heard stillen sway bars snap & carbing causes understeer - Jiro 03:14:49 01/19/13 are you planning to do a lot of track days? - LJZTT 04:12:44 01/19/13 this car will be going to the track for sure. (n/m) - Jiro 15:10:27 01/19/13 There are pros and cons to every mod. - Ghoztt 09:41:37 01/19/13 I have stillen sway bars and Carbing braces front and rear - *BK300ZX* 12:37:37 01/19/13 Think you have it backwards (t-rods and upper arms) - ZXoltan 13:37:22 01/19/13 you are correct (n/m) - ali300zx 13:43:27 01/19/13 Thanks for the clarification...i did fudge that a little. - *BK300ZX* 15:32:37 01/19/13 it will be stiffer in every aspect - LJZTT 04:11:43 01/19/13 economical list to remove wheelhop / improve handling - Jiro 16:11:05 01/19/13
Post a Followup	You cannot reply to this message because you are not logged in.