Subject	Careful, Fastener must not be tighter than washers
Posted by	BlackholeZ on January 12, 2013 at 3:57 AM
	This message has been viewed 136 times.
In Reply To	Pretty good demonstration video posted by thumper (Los Angeles) on January 12, 2013 at 12:10 AM
Message	The washer has to dig in to the fastener and base material in order for the friction to work the way they want. If the fastener or base material is harder than the washers they would work the same as a normal washer. -Dan BlackholeZ VTC Solenoid Caps Installation Procedure "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines "You're the Skrillex of Z32s." BradX (UF)
Follow Ups	Manifold to turbo nut. - rmalik23 18:47:03 01/11/13 I'm using grade 10.9 flanged lock nuts from lowes. - Lumpydonut 19:18:25 01/11/13 yet. (n/m) - TriniTT 20:13:44 01/11/13 I'd look into spiralock - aliaZ 19:19:53 01/11/13 Flange nut or self clinching? (n/m) - thumper (Los Angeles) 20:52:22 01/11/13 flange nuts (n/m) - aliaZ 21:46:37 01/11/13 Cooper lock nuts . . . We offer them (n/m) - RoyaltyPerformance 19:25:13 01/11/13 ^ These, they work well! Tried them last time engine was out (n/m) - ZinnZ32 19:28:21 01/11/13 Assuming copper - Yes? - thumper (Los Angeles) 21:05:03 01/11/13 Similar.. Flange might not fit. Copper plated steel lock nut - ZinnZ32 21:14:21 01/11/13 My link was just an example. - thumper (Los Angeles) 21:31:55 01/11/13 Lol . . yes copper (n/m) - RoyaltyPerformance 19:36:00 01/12/13 Use a high grade steel nut, the secret is... - Spectrum (WI) 22:52:09 01/11/13 which one would be recommended for manifold - aliaZ 23:13:03 01/11/13 Argh!!! you bastages- now you pull out the good stuff? - Zvil (FL) 07:25:59 01/12/13 Pretty good demonstration video - thumper (Los Angeles) 00:10:35 01/12/13 That's effing awesome! Thanks. Makes me want to get - PiotrC70 01:43:48 01/12/13 Careful, Fastener must not be tighter than washers - BlackholeZ 03:57:34 01/12/13 Ave hardness of the Nord-lock washers is a minimum C44 - Spectrum (WI) 22:10:30 01/13/13 2nd. First Time I've seen this. (n/m) - OverZealous (CT) 23:40:24 01/12/13 It's not to save your 3 dollar nuts....the reason - i-xclr8 10:03:27 01/12/13 Re: It's not to save your 3 dollar nuts....the reason - rmalik23 13:16:39 01/12/13 Grade 10.9 flanged lock nuts. Uses the same lock as the nord - Lumpydonut 14:04:24 01/12/13 Close but not quite.... - Spectrum (WI) 22:27:20 01/13/13 The closest thing I can think of are... - Spectrum (WI) 22:21:38 01/13/13 Got Lube??? - LitlElvis 10:08:09 01/12/13 I agree. Old school & basic, often overlooked, but works! (n/m) - OverZealous (CT) 23:43:37 01/12/13 Re: Manifold to turbo nut. - rmalik23 15:09:54 01/13/13
Post a Followup	You cannot reply to this message because you are not logged in.