Subject	Re: Re: unfortunately you can't really re-use the stock blose wiring
Posted by	WE350Z on December 28, 2012 at 3:15 PM
	This message has been viewed 186 times.
In Reply To	Re: unfortunately you can't really re-use the stock blose wiring posted by russ29 on December 28, 2012 at 07:36 AM
Message	easy to run the wires from behind your deck then out the side, under the floor board. You can slip the boot off (or pierce it) in the door jam. Would be hard to run the wire inside the boot. I have to run two sets one for the woofer one for the tweeter so I will probably just try to run them on the back of the boot and maybe ziptie or electric tape them. _____________________ 2006 Yamaha R1 Anniversary Edition 2006 Scion tC (Sold) 2004 Yamaha YZF-R6 (Sold) 2003 Nissan 350Z Track (Sold) 2000 BMW X5 4.4i 1993 300ZX Twin Turbo 1985 Nissan 300ZX NA (Sold) http://WE350Z.com>v WE350Z at gmail dot com
Follow Ups	My Sound System Install Saga - WE350Z 17:49:03 12/27/12 Re: My Sound System Install Saga - ztorque 17:58:24 12/27/12 Re: Re: My Sound System Install Saga - WE350Z 18:47:10 12/27/12 Re: Re: Re: My Sound System Install Saga - ztorque 19:16:32 12/27/12 unfortunately you can't really re-use the stock blose wiring - WE350Z 00:08:59 12/28/12 Re: unfortunately you can't really re-use the stock blose wiring - russ29 07:36:43 12/28/12 Re: Re: unfortunately you can't really re-use the stock blose wiring - WE350Z 15:15:41 12/28/12 Rockford Fosgate FTW - ConVerTT 18:26:44 12/27/12 Re: Rockford Fosgate FTW - WE350Z 18:54:43 12/27/12 I went back to stock front bose enclosures. - Hipendicular 18:57:07 12/27/12 dynomat would fix a lot of those issues too (n/m) - WE350Z 20:49:58 12/27/12 I'd go with B-Quiet or Fat-Mat. Dynamat is overpriced IMO. (n/m) - evan_aggie 23:23:47 12/27/12 The rattle is due to a broken bolt, not the speaker mounting - BigTDogg (MA) 09:57:56 12/28/12 I was confused by this as well - Jayru 10:28:49 12/28/12 Yep, links inside: - BigTDogg (MA) 11:01:50 12/28/12 More noise and rattle are explained and no its not a bolt - Hipendicular 21:28:20 12/28/12 The Bose drivers are 1 ohm, which may be fine for your - BigTDogg (MA) 21:45:35 12/28/12 I ohmed my bose to ~3 Ohms.. - Hipendicular 13:31:53 12/29/12 Interesting, I thought all Bose drivers for the Z32 were - BigTDogg (MA) 16:41:41 12/29/12 Yeah the Memphis Mclass Tweets are Alum/Mag.. (n/m) - Hipendicular 21:32:22 12/28/12 When I had a slow car I was big into mobile audio - Lumpydonut 22:00:55 12/27/12 I have the same amp. I need something smaller :-( (n/m) - johnnysombrero 00:24:26 12/28/12
Post a Followup	You cannot reply to this message because you are not logged in.