Subject	coo!think i'll do that.
Posted by	RonDeezy on October 25, 2012 at 4:57 AM
	This message has been viewed 171 times.
In Reply To	Re: z1 ptu relocation kit fail posted by JUNz (?00)rwhp on October 25, 2012 at 04:40 AM
Message	today was kinda long.but im glad i pulled out my accordions.i found that whatever crap ass shop installed the motor didnt even use clamps in a couple sketchy places.found one missing on a j pipe and another on the driver accordion to be exact.now im just debating on if i should install my underdrive pulleys while im at it.i also have an oem timing belt along with a kevlar one just chillin.not to mention a new water pump too.so temping....
Follow Ups	z1 ptu relocation kit fail - RonDeezy 18:09:40 10/24/12 I wouldn't pay for something that easily made. (n/m) - SWhiteTT(GA) 18:21:42 10/24/12 No good reason to put it there anyway. (n/m) - Bernie (NoVA) 18:38:55 10/24/12 False (n/m) - vorpalZ 10:37:25 10/25/12 False. (n/m) - Bernie (NoVA) 20:50:36 10/25/12 You're correct, there are 3 good reasons (n/m) - vorpalZ 23:21:37 10/25/12 False. (n/m) - Bernie (NoVA) 07:25:10 10/26/12 Wow, right again, just remembered another, make that 4 (n/m) - vorpalZ 08:15:59 10/27/12 I had similar issue with the bracket they supplied to mount - LJZTT 18:39:09 10/24/12 well now im stuck with it. - RonDeezy 19:19:48 10/24/12 How is this company still in business? - Jayru 19:45:35 10/24/12 That looks flimsy as hell anyways. What gauge metal? (n/m) - Evan_Wright (Ca) 20:06:03 10/24/12 looks a lot more flimsy in the pic.not sure of the guage. - RonDeezy 20:29:37 10/24/12 What did that cost? (n/m) - ConVerTT 20:45:04 10/24/12 cost:$24, almost down the drain. - RonDeezy 21:00:47 10/24/12 Owned (n/m) - Drk93TT 20:53:16 10/24/12 You can mount it there with the same bracket you'd mount - BigTDogg (MA) 22:00:04 10/24/12 2nd (n/m) - KongZTT GT28RS MD 22:00:39 10/24/12 its all good.i figured i could use that bracket. - RonDeezy 22:08:26 10/24/12 Nose panel fits without issue. (n/m) - BigTDogg (MA) 12:18:41 10/25/12 OEM bracket for the "heat sink" characteristic (n/m) - BoneZ (MD) 22:52:11 10/24/12 When you buy a Z1 product you have to assume you're doing - 240Z FeO2 23:49:21 10/24/12 Had the same problem here and they wouldnt return it. - DSM_EX-DRIVER 01:44:11 10/25/12 Re: z1 ptu relocation kit fail - JUNz (?00)rwhp 04:40:25 10/25/12 coo!think i'll do that. - RonDeezy 04:57:31 10/25/12 Do it. - TTZEDHEAD 05:57:32 10/25/12 Or just use a stock bolt location - Woody75 (Denver) 09:57:12 10/25/12 Seriously BOUGHT that? hmmm.. that (sorry) - MidLifeZ (DFW) 07:49:28 10/25/12 you should have just used that money as a target and - John90zxtt(OH) 07:55:22 10/25/12 ^^^^^ this. (n/m) - spicyZ 09:26:01 10/25/12 Ha! (n/m) - Schmeal 12:18:39 10/25/12 You'll have a current design replacement tomorrow. - Russell@Z1 08:47:56 10/25/12 C'mon man! (n/m) - ConVerTT 09:05:59 10/25/12 Thanks for owning up Russell. - Zsgetyoulaid 10:10:31 10/25/12 And for proving the point made in my post above (n/m) - 240Z FeO2 17:59:36 10/25/12 Why not call the vendor before complaining on this - njz 10:38:34 10/25/12 ....it was purchased over a year ago. - RonDeezy 12:08:39 10/25/12 It don't matter, vendors will make things right - njz 20:15:03 10/25/12 Re: ....it was purchased over a year ago. - team7 17:26:44 10/26/12 90% of the time when I email z1 about a product only they - fuzzymonkey 12:23:05 10/25/12 I suggest calling if you are offended with the brevity of - Russell@Z1 12:48:30 10/25/12 repost!!!!!!!!!!!!!!!!!! - HighPsi (NorCal) 13:18:35 10/25/12
Post a Followup	You cannot reply to this message because you are not logged in.