Subject	Having held both OEM and MSP manifolds in my hands
Posted by	Evan(CA) on October 02, 2012 at 3:48 PM
	This message has been viewed 274 times.
In Reply To	I'm thinking manifolds posted by LJZTT on October 02, 2012 at 03:32 PM
Message	I have no doubt the MSP's would provide significant gains. My question is are the TB's worth it at all? Why is "machining" the plenum to accept the larger TB's such a chore? I'm not talking about extrude honing the plenum or anything like that. I was under the impression you basically bolt up the new larger TB gasket, trace a line around the inside and carefully grind away the opening until the hole is the correct size. Am I wrong?
Follow Ups	How effective are larger TB's? - Evan(CA) 13:44:32 10/02/12 This is a great question, and I look forward to the answer - Haasz32 14:45:27 10/02/12 you will get someone telling you that it'll be a bottleneck - fuzzymonkey 15:09:45 10/02/12 Sounds like you've changed your tune :) - Evan(CA) 16:31:59 10/02/12 wow, nice find! for a site i'm NEVER on... - fuzzymonkey 17:14:54 10/02/12 I only remembered it because I was the OP of the thread. - Evan(CA) 17:42:59 10/02/12 Difinately not worth the gains considering the head aches - Evan_Wright (Ca) 15:20:28 10/02/12 I'm thinking manifolds - LJZTT 15:32:08 10/02/12 Having held both OEM and MSP manifolds in my hands - Evan(CA) 15:48:44 10/02/12 It is as easy as you say. I used a die grinder. (n/m) - Evan_Wright (Ca) 16:01:00 10/02/12 Well like I said, my situation is likely different.... - LJZTT 16:52:09 10/02/12 all you need to do is enlarge the plenum intake - vorpalZ 17:20:05 10/02/12 Its soft aluminum. not even that hard to do with a dremel. (n/m) - Antihero 11:29:57 10/03/12 if you have all afternoon... :) (n/m) - vorpalZ 14:38:03 10/03/12 Id be surprised if it took me more than an hour. - Antihero 10:45:37 10/04/12 you mean for stanza or for z1? - Antihero 15:54:13 10/02/12 Die grinder with Al cutting/grinding tip, 10 min/side - vorpalZ 15:58:51 10/02/12 bing - fucking - DOE! .... dremel tool works wonders (n/m) - genic 15:40:51 10/04/12 Did you do Stanza TBs or RobZ/Z1? - BlackholeZ 17:04:58 10/03/12 Check out what Rob'Z did. - TheMarlin (MidTN) 17:22:50 10/02/12 The low end gain is not correct . - ArubaDave 18:09:03 10/02/12 Sure enough. - TheMarlin (MidTN) 21:57:26 10/02/12 Not entirely true - Rob'Z 23:30:31 10/02/12 I see - ArubaDave 08:16:15 10/03/12 Re: How effective are larger TB's? - KA8 04:16:45 10/03/12 An important point to remember when going to larger TBs - BlackholeZ 17:19:13 10/03/12 there is a solution to opening resolution by changing the - Dane (Houston) 23:05:16 10/03/12 very nice...thanks for that (n/m) - aliaZ 06:58:55 10/04/12 Exactly, that's what I meant by throttle pulley. - BlackholeZ 15:15:50 10/04/12 Throttle modulation didn't seem to be much of an issue after - maglito 20:46:16 10/05/12
Post a Followup	You cannot reply to this message because you are not logged in.