Subject	In my opinion no. The box covers the entire bracket area
Posted by	Jayru on October 01, 2012 at 2:59 PM
	This message has been viewed 220 times.
In Reply To	Is it possible to remove the bolts from the bracket posted by TriniTT on October 01, 2012 at 11:26 AM
Message	Not any room for a mirror or anything in there. The top nut for the bracket is way high above the harness. I would take pics for you of mine, but I split my arm open yesterday working on the car (unrelated to the harness). 15 stitches later, I'm not doing much today. 90 Twin Turbo Track Build - jsworks.org for more info!
Follow Ups	EFI Harness Replacement - ZXRider 23:40:55 09/30/12 tilt motor as far forward as you can to get access to FW (n/m) - Bernie (NoVA) 00:10:42 10/01/12 If I put a transmission jack under the transmission - ZXRider 00:19:04 10/01/12 disconnect DS, exhaust, upper rad hose & intake couplers. (n/m) - Bernie (NoVA) 00:51:31 10/01/12 Remove the plastic outer cover on the efi F1 connector. - TriniTT 08:23:49 10/01/12 Disconnect your AC box and remove from the glove box - Jayru 09:13:03 10/01/12 yep - aliaZ 09:53:14 10/01/12 Never heard that before - ZXRider 10:09:06 10/01/12 It's a black box behind the glove box - Jayru 11:19:02 10/01/12 I see - ZXRider 11:26:54 10/01/12 Were you able to remove the ac box without removing the dash - TriniTT 10:48:17 10/01/12 Sure. The skeleton frame of the glove box - Jayru 11:12:43 10/01/12 don't forget you need to disconnect your AC lines (n/m) - aliaZ 11:19:54 10/01/12 Why - lower AC box comes off w/out disconnecting the - jzack 12:32:39 10/01/12 Not the evaporator box (n/m) - ZXoltan 12:41:44 10/01/12 are you saying the lower half of the evaporator box - aliaZ 14:23:46 10/01/12 The bracket is all the way at the top of the firewall inside - Jayru 14:55:25 10/01/12 ok, thanks for the clarification - aliaZ 15:07:31 10/01/12 Is it possible to remove the bolts from the bracket - TriniTT 11:26:28 10/01/12 In my opinion no. The box covers the entire bracket area - Jayru 14:59:56 10/01/12 not necessary and from what it looked to me, almost as - LJZTT 12:50:43 10/01/12 This is what I did, worked fine... (n/m) - Red Hawk (CO) 13:02:25 10/01/12 putting it in is easier than pulling out the harness - ztunerz 13:43:56 10/01/12 How did you get the new one in? Pull the motor? - ZXRider 13:49:30 10/01/12 sold my soul, was a fair deal (n/m) - LJZTT 14:26:56 10/01/12 This is what I originally thought. But after 15 min the box - Jayru 15:10:31 10/01/12 I have a few cans of R-12 left. - ZXoltan 15:59:56 10/01/12 How did you dump the freon? Just curious how you let - ZXRider 22:19:54 10/02/12 See i told ya :) (n/m) - ztunerz 13:42:34 10/01/12 Smart advice ;-) (n/m) - Jayru 14:49:42 10/01/12 Have never found a need or desire to mess w. that. (n/m) - Bernie (NoVA) 01:58:55 10/02/12 2nd. - Woody75 (Denver) 09:40:25 10/02/12 The only times I've changed a harness is while the engine is - aliaZ 14:47:50 10/02/12 I just did this last summer, and most tips have been covered - LJZTT 14:24:41 10/01/12 helpful pic of a clasp you wont be able to see, but get your - LJZTT 14:43:59 10/01/12 Great. Thank you for the photos and your instructions. (n/m) - ZXRider 16:12:32 10/01/12 I've actually had this pic saved on my phone for some time. - TriniTT 15:30:19 10/01/12 EFI Harness Replacement - JMartz 15:26:52 10/01/12
Post a Followup	You cannot reply to this message because you are not logged in.