Subject	There are several factors to consider.
Posted by	rojoloco (VA Beach) on September 22, 2012 at 12:30 AM
	This message has been viewed 267 times.
In Reply To	Re: Powertrix has fixed this problem as well. posted by Rob260 on September 21, 2012 at 06:57 AM
Message	One, are the arms being installed correctly? Incorrect install will cause them to fail sooner because they are being forced into a position they were never meant to be in. Two, are the arms being overextended to compensate for travel? This is where the extended center section comes into play. Assuming there is a proper amount of thread still in the sleeve, there shouldn't really be any reason for them to bend or break. ----------------------------------------------------- Never Play Leapfrog With A Unicorn!!! WILL JSCHRAUWEN EVER ANSWER MY QUESTION? John, stop it! You are not allowed in AMS threads and you know it. -- marty1mc Do yourself a favor and just worry about your own car. I don't see what everyone is so worried about anyway. If someone else wants to perform a modification that you believe will destroy the value, cheapen the Z32 or whatever you can't sit on your hands about, wouldn't that make your tastefully-modified, white bread Z32 more rare and valuable? -- BradZ (FL) on December 23, 2007 at 12:19 PM The unicorn gets its revenge... -- Scotts94z32 on September 19, 2006 at 11:12 AM CLICK FOR DETAILS ABOUT BUYING A ZAMA POSTER!!!!
Follow Ups	Be careful ! Many front upper adj. arms bend after few years - RomChip200 03:24:53 09/21/12 All the front adj. arms (current design) are going to bend - RomChip200 03:40:34 09/21/12 Re: All the front adj. arms (current design) are going to bend - Rob260 05:51:14 09/21/12 Re: Re: All the front adj. arms (current design) are going to bend - Rob260 05:52:29 09/21/12 Re: Re: Re: All the front adj. arms (current design) are going to bend - RomChip200 07:54:48 09/21/12 Re: Re: Re: Re: All the front adj. arms (current design) are going to bend - Rob260 23:35:05 09/22/12 Re: Re: Re: Re: All the front adj. arms (current design) are going to bend - Rob260 00:52:20 09/23/12 SPL should have a new arm out that solves this issue. (n/m) - MixManMash 05:07:40 09/21/12 Re: SPL should have a new arm out that solves this issue. - Rob260 05:45:00 09/21/12 Negative. I think they had a set back (sort of), but Sean - evan_aggie 07:57:10 09/21/12 Yes I saw the prototype here at Zcon... QUALITY! - Piranha 08:18:51 09/21/12 Powertrix has fixed this problem as well. - rojoloco (VA Beach) 06:52:30 09/21/12 Re: Powertrix has fixed this problem as well. - Rob260 06:57:32 09/21/12 There are several factors to consider. - rojoloco (VA Beach) 00:30:26 09/22/12 Powertrix and knock-offs have exactly this bent problem ! (n/m) - RomChip200 07:39:41 09/21/12 eh...no they haven't (n/m) - aliaZ 08:59:24 09/21/12 Well, what did they do to avoid it ? (n/m) - RomChip200 09:27:41 09/21/12 I'm sorry but both designs look the same - RomChip200 09:31:56 09/21/12 Was that the amount extended? - njz 10:46:22 09/21/12 umm...I'm saying that Powertrix didn't fix the problem (n/m) - aliaZ 12:56:01 09/21/12 false (n/m) - Adam (NoVA) 17:58:46 09/21/12 Did yours fail? If so did you install to spec? - njz 08:11:45 09/21/12 Re: Did yours fail? If so did you install to spec? - RomChip200 09:02:03 09/21/12 Is that the actual length of your FUCA when removed? - njz 10:58:01 09/21/12 The 300 Degree kit can be used behind an Aftermarket UFCA - Gordo 93TT Daytona 10:01:34 09/21/12 I'm sorry I don't follow many of you - RomChip200 10:11:36 09/21/12 I was always felt uncomfortable when I had FUCAS and RUCAS - KA8 10:49:43 09/21/12 I Have the newest Stillen design so you're saying mine will - craigz96tt 09:54:36 09/21/12 Yes - Jayru 12:56:53 09/21/12 Solution? Get adjustable front Lower control arm for camber - RevTech 15:19:39 09/21/12 Who still makes that? I see some GSP products, but that is - evan_aggie 15:37:10 09/21/12 Re: Who still makes that? I see some GSP products, but that is - Rob260 00:53:30 09/23/12 here - aliaZ 14:03:02 09/23/12 instead of expecting us to take your word for it - aliaZ 14:15:06 09/23/12 Re: instead of expecting us to take your word for it - Rob260 17:58:21 09/23/12
Post a Followup	You cannot reply to this message because you are not logged in.