Subject	Who still makes that? I see some GSP products, but that is
Posted by	evan_aggie on September 21, 2012 at 3:37 PM
	This message has been viewed 219 times.
In Reply To	Solution? Get adjustable front Lower control arm for camber posted by RevTech on September 21, 2012 at 03:19 PM
Message	ebay junk, right?
Follow Ups	Be careful ! Many front upper adj. arms bend after few years - RomChip200 03:24:53 09/21/12 All the front adj. arms (current design) are going to bend - RomChip200 03:40:34 09/21/12 Re: All the front adj. arms (current design) are going to bend - Rob260 05:51:14 09/21/12 Re: Re: All the front adj. arms (current design) are going to bend - Rob260 05:52:29 09/21/12 Re: Re: Re: All the front adj. arms (current design) are going to bend - RomChip200 07:54:48 09/21/12 Re: Re: Re: Re: All the front adj. arms (current design) are going to bend - Rob260 23:35:05 09/22/12 Re: Re: Re: Re: All the front adj. arms (current design) are going to bend - Rob260 00:52:20 09/23/12 SPL should have a new arm out that solves this issue. (n/m) - MixManMash 05:07:40 09/21/12 Re: SPL should have a new arm out that solves this issue. - Rob260 05:45:00 09/21/12 Negative. I think they had a set back (sort of), but Sean - evan_aggie 07:57:10 09/21/12 Yes I saw the prototype here at Zcon... QUALITY! - Piranha 08:18:51 09/21/12 Powertrix has fixed this problem as well. - rojoloco (VA Beach) 06:52:30 09/21/12 Re: Powertrix has fixed this problem as well. - Rob260 06:57:32 09/21/12 There are several factors to consider. - rojoloco (VA Beach) 00:30:26 09/22/12 Powertrix and knock-offs have exactly this bent problem ! (n/m) - RomChip200 07:39:41 09/21/12 eh...no they haven't (n/m) - aliaZ 08:59:24 09/21/12 Well, what did they do to avoid it ? (n/m) - RomChip200 09:27:41 09/21/12 I'm sorry but both designs look the same - RomChip200 09:31:56 09/21/12 Was that the amount extended? - njz 10:46:22 09/21/12 umm...I'm saying that Powertrix didn't fix the problem (n/m) - aliaZ 12:56:01 09/21/12 false (n/m) - Adam (NoVA) 17:58:46 09/21/12 Did yours fail? If so did you install to spec? - njz 08:11:45 09/21/12 Re: Did yours fail? If so did you install to spec? - RomChip200 09:02:03 09/21/12 Is that the actual length of your FUCA when removed? - njz 10:58:01 09/21/12 The 300 Degree kit can be used behind an Aftermarket UFCA - Gordo 93TT Daytona 10:01:34 09/21/12 I'm sorry I don't follow many of you - RomChip200 10:11:36 09/21/12 I was always felt uncomfortable when I had FUCAS and RUCAS - KA8 10:49:43 09/21/12 I Have the newest Stillen design so you're saying mine will - craigz96tt 09:54:36 09/21/12 Yes - Jayru 12:56:53 09/21/12 Solution? Get adjustable front Lower control arm for camber - RevTech 15:19:39 09/21/12 Who still makes that? I see some GSP products, but that is - evan_aggie 15:37:10 09/21/12 Re: Who still makes that? I see some GSP products, but that is - Rob260 00:53:30 09/23/12 here - aliaZ 14:03:02 09/23/12 instead of expecting us to take your word for it - aliaZ 14:15:06 09/23/12 Re: instead of expecting us to take your word for it - Rob260 17:58:21 09/23/12
Post a Followup	You cannot reply to this message because you are not logged in.