Subject	ok pal (n/m)
Posted by	TTkickedin on September 15, 2012 at 2:23 PM
	This message has been viewed 216 times.
In Reply To	don't half-ass posted by LJZTT on September 15, 2012 at 07:46 AM
Message
Follow Ups	18x10 square fitment? - TTkickedin 14:20:58 09/14/12 Will not fit, definitely not on the front and most likely - RAGTPZ 14:31:52 09/14/12 Don't cut coils by the way, it is dangerous to drive like - RAGTPZ 14:35:28 09/14/12 I drove a 98 Legacy gt with too much cut from the springs... - TTkickedin 15:07:56 09/14/12 "Not that much" is too much. Dont cut your springs. (n/m) - white22sky 16:28:13 09/14/12 Do research.I really don't feel like havign a debate about - TTkickedin 16:36:31 09/14/12 don't half-ass - LJZTT 07:46:31 09/15/12 ok pal (n/m) - TTkickedin 14:23:16 09/15/12 You are flat out wrong. Cutting coils is not safe, and - Gordo 93TT Daytona 16:43:24 09/14/12 Right, Leaving the coil rounded as opposed to plasma cutting - TTkickedin 16:49:07 09/14/12 The diameter of the spring narrows at both ends. If you - Gordo 93TT Daytona 19:12:52 09/14/12 Re: The diameter of the spring narrows at both ends. If you - TTkickedin 10:48:41 09/15/12 If you want to cut coils and cheap out, buy a honda civic. - intel 11:34:42 09/15/12 keep researching, youll find another credible source of info - TTkickedin 14:18:46 09/15/12 no one is pissed off - vulcanrush 14:24:27 09/15/12 apparently you do since you all are giving me these random - TTkickedin 14:28:55 09/15/12 OK cut the coils, it's your car. But don't disrespect us. - Gordo 93TT Daytona 12:18:56 09/15/12 Re: OK cut the coils, it's your car. But don't disrespect us. - TTkickedin 14:10:51 09/15/12 Next time I'll just VTD. (n/m) - Gordo 93TT Daytona 16:16:38 09/15/12 you don't talk to someone like Gordo like that, dummy (n/m) - ali300zx 12:45:53 09/15/12 lol but i think i did.as far as im concerned - TTkickedin 14:22:31 09/15/12 lol, they have internet service in the McDonald's kitchen? - LJZTT 07:56:52 09/15/12 thanks for your opinion, cool story. bro (n/m) - TTkickedin 10:44:46 09/15/12 You're not going to last here long. - BannonZ 08:29:02 09/15/12 its a forum, youre taking yourself too seriously (n/m) - TTkickedin 10:40:22 09/15/12 says the guy taking time to reply to every single criticism (n/m) - LJZTT 18:19:22 09/15/12 i must be doing something right. - TTkickedin 23:49:04 09/16/12 Re: 18x10 square fitment? - JRFITZ 14:40:48 09/14/12 How Much? They're okay, not exactly the fitment - TTkickedin 15:01:44 09/14/12 Re: How Much? They're okay, not exactly the fitment - JRFITZ 16:40:09 09/14/12 hows the tires? - TTkickedin 15:37:07 09/15/12 18x10 +48 wont poke, However you will hit the strut/spring.. - ZinnZ32 14:54:39 09/14/12 Very useful information, thanks for the post. - TTkickedin 15:00:25 09/14/12 Please do know that 18x10 +48 is very high offset still... - ZinnZ32 15:13:37 09/14/12 Yeah, I was aware of that when I was reading the descrip - TTkickedin 15:20:30 09/14/12 And I do plan to roll my fenders, front to back. - TTkickedin 15:25:04 09/14/12 Front Fender area is where you have to worry. - ZinnZ32 15:31:13 09/14/12 Stock camber, Might opt for 15mm spacers, the legit kind - TTkickedin 16:22:28 09/14/12 In addition to the wheels, here's what will make them fit - TTkickedin 16:31:16 09/14/12 Get the Groundcontrol Lower kit. - XTZ 15:50:58 09/14/12 +1 I love my GC kit (n/m) - Red Hawk (CO) 16:14:47 09/14/12 Never was the intention to get ebay coilovers! - TTkickedin 16:25:36 09/14/12 Installing isn't very hard, you'll need an impact wrench (n/m) - XTZ 20:30:02 09/14/12 Those don't address his concern about the spring at full - dogpile 22:49:13 09/14/12 It will fit... - Bigwill837 17:33:54 09/14/12 lulz (n/m) - Antihero 17:39:48 09/14/12 is 3ZC redirecting to TTnet? (n/m) - LJZTT 07:59:11 09/15/12 I ran 18x10 x4 285s on all corners. - maglito 05:51:11 09/17/12 Love that car! (n/m) - KongZTT GT28RS MD 22:13:45 09/18/12 if you cut your springs...there goes another good Z - genic 22:35:47 09/15/12
Post a Followup	You cannot reply to this message because you are not logged in.