Subject	Just need 6 ton jackstands and a jack with a stroke of
Posted by	BigTDogg (MA) on September 14, 2012 at 1:46 PM
	This message has been viewed 174 times.
In Reply To	I will take all this info posted by boostlv on September 14, 2012 at 01:40 PM
Message	18+ inches. The taller the better. If you're not sliding the tranny out from under the car, you don't even need it that high. One company you should never buy from Z32 Enthusiast Group On FB "I was way more timid then than I am now about getting in there and yanking on things." - TT XTZ 13:30:34 07/25/05 "...Downpipes own. I love them...I shall name my first-born after them with glee..." - SeedyRom 05:13:20 10/03/02 "Just ran out to get some knee pads. I'm ready now... BRING.....IT.....ON... :-) " - Dave N 19:04:30 10/31/07 "Either ignore him or beat him up. Anything else will be over his head." - Marshall 12:28:23 08/18/04 "I hope you get fucked in the ass with a pringles can." - ni[X]it 14:53:53 02/02/06 "I'm glad I have the MSP mani's." - jschrauwen 22:20:13 06/10/08 "i love the cock" - genic 22:20:47 09/25/03
Follow Ups	How difficult is it to change the clutch? - boostlv 21:14:28 09/13/12 The Z is not the car to teach clutch 101 - Barry(TN) 22:02:36 09/13/12 I respectfully disagree. - AHos(Chicago) 23:25:02 09/13/12 I gotta say that it's pretty easy - BlackholeZ 01:38:51 09/14/12 3'rded. Z's really not too bad. (n/m) - Antihero 11:09:35 09/14/12 take a weekend, on flat surface and take your time. - live4strength 16:52:37 09/14/12 Its not to terribly bad - DomZ32TT 22:42:31 09/13/12 Get a tranny jack unless your built like the hulk - s3trios 23:18:52 09/13/12 I use 2 jacks.. just have to be very careful with placement (n/m) - AHos(Chicago) 23:25:34 09/13/12 A floor jack and helper does the job (on jackstands) - BlackholeZ 01:41:57 09/14/12 I two decent size guys can handle it easily. - Antihero 07:40:25 09/14/12 Also the most dangerous. (n/m) - Bernie (NoVA) 08:10:30 09/14/12 I just lowered it onto my chest and crawled out with it ;) (n/m) - Red Hawk (CO) 11:57:05 09/14/12 Yes. 5spd trans isn't all that heavy really (n/m) - Zu4ea 12:33:49 09/14/12 It will mame or kill if not careful. (n/m) - Bernie (NoVA) 15:19:33 09/15/12 It will take a while and you'll need patience - CoHPhasor 02:02:14 09/14/12 The first major repair i performed on my Z was the clutch... - 90TT Zfan (E.Tenn) 07:08:46 09/14/12 Same here. Budget twice the time you think. - johnnysombrero 07:48:16 09/14/12 Caution w/ jackstand placement. 18" clearance. Floorjack OK - Gordo 93TT Daytona 08:42:44 09/14/12 2nd on making sure all is stable. I built wood block - jzack 22:28:03 09/14/12 If you can spare the 360 have it done - njz 09:02:41 09/14/12 I will take all this info - boostlv 13:40:13 09/14/12 Just need 6 ton jackstands and a jack with a stroke of - BigTDogg (MA) 13:46:31 09/14/12
Post a Followup	You cannot reply to this message because you are not logged in.