Subject	A floor jack and helper does the job (on jackstands)
Posted by	BlackholeZ on September 14, 2012 at 1:41 AM
	This message has been viewed 196 times.
In Reply To	Get a tranny jack unless your built like the hulk posted by s3trios on September 13, 2012 at 11:18 PM
Message	and you will want 4 of them. One guy guiding, one guy to steady and push from the rear, and a jack to hold the weight. -Dan BlackholeZ VTC Solenoid Caps Installation Procedure "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines "You're the Skrillex of Z32s." BradX (UF)
Follow Ups	How difficult is it to change the clutch? - boostlv 21:14:28 09/13/12 The Z is not the car to teach clutch 101 - Barry(TN) 22:02:36 09/13/12 I respectfully disagree. - AHos(Chicago) 23:25:02 09/13/12 I gotta say that it's pretty easy - BlackholeZ 01:38:51 09/14/12 3'rded. Z's really not too bad. (n/m) - Antihero 11:09:35 09/14/12 take a weekend, on flat surface and take your time. - live4strength 16:52:37 09/14/12 Its not to terribly bad - DomZ32TT 22:42:31 09/13/12 Get a tranny jack unless your built like the hulk - s3trios 23:18:52 09/13/12 I use 2 jacks.. just have to be very careful with placement (n/m) - AHos(Chicago) 23:25:34 09/13/12 A floor jack and helper does the job (on jackstands) - BlackholeZ 01:41:57 09/14/12 I two decent size guys can handle it easily. - Antihero 07:40:25 09/14/12 Also the most dangerous. (n/m) - Bernie (NoVA) 08:10:30 09/14/12 I just lowered it onto my chest and crawled out with it ;) (n/m) - Red Hawk (CO) 11:57:05 09/14/12 Yes. 5spd trans isn't all that heavy really (n/m) - Zu4ea 12:33:49 09/14/12 It will mame or kill if not careful. (n/m) - Bernie (NoVA) 15:19:33 09/15/12 It will take a while and you'll need patience - CoHPhasor 02:02:14 09/14/12 The first major repair i performed on my Z was the clutch... - 90TT Zfan (E.Tenn) 07:08:46 09/14/12 Same here. Budget twice the time you think. - johnnysombrero 07:48:16 09/14/12 Caution w/ jackstand placement. 18" clearance. Floorjack OK - Gordo 93TT Daytona 08:42:44 09/14/12 2nd on making sure all is stable. I built wood block - jzack 22:28:03 09/14/12 If you can spare the 360 have it done - njz 09:02:41 09/14/12 I will take all this info - boostlv 13:40:13 09/14/12 Just need 6 ton jackstands and a jack with a stroke of - BigTDogg (MA) 13:46:31 09/14/12
Post a Followup	You cannot reply to this message because you are not logged in.