Subject	89mm
Posted by	BLACK Z on August 21, 2012 at 1:30 AM
	This message has been viewed 197 times.
In Reply To	overbored to 3.03L nice thanks man (n/m) posted by Jiro on August 20, 2012 at 10:04 PM
Message	I have a 3.1 litre with 89mm pistons (3098cc ) this is the absolute max you would go (with the right block) to run at any decent power level I have sonic tested a few blocks and the core shift on these blocks is pretty bad .
Follow Ups	Overbored to 3.3L - Jiro 10:44:10 08/20/12 the previous owner is lying to you. - aliaZ 11:08:59 08/20/12 2nd. (n/m) - SimaYi 13:30:30 08/20/12 Biggest 3rd ever! (n/m) - The Hawk 15:02:23 08/20/12 That's something you check before buying. (n/m) - SactoTodd 11:37:39 08/20/12 Isn't the engine from IPP? Can't you check with Kyle? (n/m) - Aqualung 11:57:43 08/20/12 Er... You ask to see the receipts (n/m) - vorpalZ 12:58:59 08/20/12 maybe he meant 3.2 (n/m) - mikehawkhertz 13:33:24 08/20/12 Re: maybe he meant 3.2 - Antihero 13:42:50 08/20/12 JUN stroker kit, and no radiator shroud FTW!! (n/m) - BigTDogg (MA) 14:32:11 08/20/12 I was wrong here. 92 unsleeved isn't going to happen (n/m) - Antihero 07:32:04 08/21/12 still unlikely with a stock stroke - aliaZ 14:49:10 08/20/12 I have 3.2L - sparkie 15:39:48 08/20/12 Devin was sleeved, right? (n/m) - Antihero 16:07:55 08/20/12 I think he sold the kit before finishing it - aliaZ 16:26:23 08/20/12 No. It was not sleeved. (n/m) - sparkie 21:59:37 08/20/12 are you thinking about this kit? - aliaZ 23:56:10 08/20/12 Pretty sure it was 93mm back then. - sparkie 00:49:03 08/21/12 i think he had 92 sleeved on a build before the paeco one. - Antihero 07:04:37 08/21/12 ok...do you know the acceptance criteria on the sonic test? - aliaZ 16:28:04 08/20/12 Re: ok...do you know the acceptance criteria on the sonic test? - sparkie 22:32:42 08/20/12 And the non-thrust side can be a little thinner. (n/m) - sparkie 00:46:03 08/21/12 are these numbers before or after boring the block? - aliaZ 05:34:35 08/21/12 I found a few threads about this.... - aliaZ 06:03:45 08/21/12 Those were before numbers - sparkie 10:59:07 08/21/12 Another factor to consider... - sparkie 16:23:08 08/21/12 you'd be crazy to go as low as .060" - aliaZ 16:47:44 08/21/12 Re: you'd be crazy to go as low as .060" - BLACK Z 01:36:13 08/22/12 yep...core shift can be pretty bad (n/m) - aliaZ 10:02:44 08/22/12 Maybe the seller meant 3.03, not 3.3 - i_s_64 15:00:43 08/20/12 And getting the VG30DE bored out to 92mm is - i_s_64 15:07:45 08/20/12 Re: Overbored to 3.3L - ali300zx 16:01:26 08/20/12 88mm = 3.03L - aliaZ 16:25:36 08/20/12 Re: 88mm = 3.03L - sky z 17:28:55 08/20/12 overbored to 3.03L nice thanks man (n/m) - Jiro 22:04:27 08/20/12 89mm - BLACK Z 01:30:28 08/21/12 Re: 89mm - sky z 04:59:28 08/21/12 Re: 89mm - MikeC(NZ) 05:49:25 08/21/12 agree 100% - aliaZ 06:08:46 08/21/12 Re: Re: 89mm - BLACK Z 07:15:16 08/21/12 Re: Overbored to 3.3L - sky z 07:03:19 08/21/12 Re: Overbored to 3.3L - sky z 06:57:31 08/22/12 ouch (n/m) - aliaZ 10:04:01 08/22/12 lol (n/m) - ZiNnYc 07:22:53 08/22/12
Post a Followup	You cannot reply to this message because you are not logged in.