Subject	I have used both Ashspec and concept z pipes
Posted by	PULSAR GTR on June 26, 2012 at 8:27 AM
	This message has been viewed 274 times.
In Reply To	Ashspec 2.5" intake kit sucks! posted by coma_ass on June 25, 2012 at 11:16 PM
Message	Both are fine, did not have any issues with them. I used the AShspec pipings on GT28RS and conceptz on GT28R, both fitted fine. your turbo is still clocked in correctly, you don't need to remove the engine out 5 times to clock the turbos. you can clock them correctly on the first try while the engine is out. I have used Ashs chip on my Z and never had an issue with it. Ash is very well respected member in the Z community and I am pretty sure he will take care of you. You should take it with Ash before you vent out on the forum, I do understand your frustration, but these 2.5 inch pipes aren't fun to install, first set I did took me half a day just to figure them out ( I was swearing up and down that is because I never isntalled them before and they are insanly tight fit espcially if you have after market radiator), the second time I installed them, took me couple of hours and did not have any issues. Both Ash and Coz from Concept Z have amazing customer service. Good luck, Rafi
Follow Ups	Ashspec 2.5" intake kit sucks! - coma_ass 23:16:12 06/25/12 Uh oh. (n/m) - ForceFedTT (SoCal) 23:28:25 06/25/12 Re: Ashspec 2.5" intake kit sucks! - 94ttz32 23:32:48 06/25/12 They are not backwards. - coma_ass 00:22:17 06/26/12 How do you know the CZP fits better in YOUR car? - evan_aggie(ATX) 23:45:37 06/25/12 Good questions. - coma_ass 00:43:41 06/26/12 CZP makes an inlet piping kit?? (n/m) - ZXoltan 23:52:30 06/25/12 Just by looking at the second pic I can tell you - michaell32 00:14:42 06/26/12 I get why you would think that, but... - coma_ass 01:55:50 06/26/12 Why not take it up with Ash? (n/m) - ForceFedTT (SoCal) 03:26:46 06/26/12 Re: Why not take it up with Ash? - Tech@EPR 04:54:25 06/26/12 I think people need to know. - coma_ass 10:29:33 06/26/12 Appreciate the warning about the shavings (n/m) - OverZealous (CT) 20:12:57 06/26/12 I just don't understand people. - njz 05:39:37 06/26/12 Hmm. My Inlet pipes fit really good. - Boosted1 05:52:52 06/26/12 On a positive note, your motor mounts are nice! ;) (n/m) - LitlElvis 06:50:13 06/26/12 The Noltec ones in the last pic ? :-) (n/m) - ArubaDave 09:33:49 06/26/12 That was before, here is after - njz 11:41:11 06/26/12 I wonder why. (n/m) - njz 09:47:30 06/26/12 I belive you might the turbos clocked wrong - TReedsZ 06:53:49 06/26/12 No issues here - Alan(MD/NJ) 07:20:37 06/26/12 2nd - Evan(CA) 11:17:42 06/26/12 You must be the first person with this complaint. - MixManMash 07:25:03 06/26/12 Is it possible its because you're running GT2560r's - ZXoltan 08:06:16 06/26/12 I just read his profile and noticed that. - michaell32 08:49:55 06/26/12 I have the S15 turbos that I bought from FRsport - HighPsi (NorCal) 11:33:06 06/26/12 I have used both Ashspec and concept z pipes - PULSAR GTR 08:27:15 06/26/12 schooled! (n/m) - MidLifeZ (DFW) 08:54:13 06/26/12 You don't have any manifolds listed? - BoneZ (MD) 09:11:22 06/26/12 No Problems here... - Zski 09:39:53 06/26/12 Yeah i had no problems with mine when i got them in right. - z-u-later 09:42:35 06/26/12 I think its the wierd turbos you're using - Red Hawk (CO) 09:49:05 06/26/12 Nothing "wierd" about the turbos - ZXoltan 11:11:16 06/26/12 Sounds like frustrated user error. (n/m) - Draker (Eugene, OR) 11:29:31 06/26/12 Crush one of those pipes with your hand and post a pic. - TheMarlin 11:39:29 06/26/12 Re: Crush one of those pipes with your hand and post a pic. - PULSAR GTR 12:20:02 06/26/12 Aren't the intake bolt locations different for those turbos - Woody75 (Denver) 12:23:03 06/26/12 yep, I used the plate adaptors for the stock piping - coma_ass 14:57:38 06/26/12 Ok, they should be good then. - Woody75 (Denver) 15:17:26 06/26/12 BTW should't use non reinforced silicone for anything beside - Bernie (NoVA) 13:04:37 06/26/12 yep, its reinforced silicone coolant line. - coma_ass 14:52:06 06/26/12 Cool - I pref. the constant tension clamps over set screw - Bernie (NoVA) 14:56:58 06/26/12 wait til you get to the filters (n/m) - ZonaZ 13:23:28 06/26/12 Did you ever get them to fit right? (n/m) - Piranha 21:42:49 06/26/12 Hmm - 90GoldZ 15:18:39 06/26/12 No problem with mine. (n/m) - PiotrC70 22:35:12 06/26/12 I think you should have a local member who has installed - michaell32 22:54:09 06/26/12 Re: I think you should have a local member who has installed - 94ttz32 23:08:31 06/26/12
Post a Followup	You cannot reply to this message because you are not logged in.