Subject	end caps and rod bolts should be the main stress points
Posted by	Red Hawk (CO) on June 20, 2012 at 4:24 PM
	This message has been viewed 212 times.
In Reply To	assuming you wanted a billet crank and light rods... posted by Antihero on June 20, 2012 at 03:21 PM
Message	I can't see a reason for needing to increase size of bearings for defense against increased rod speed... that would be saying that the rods are being allowed to be pulled apart to cause damage to the bearing. TT BEAST IN PROGRESS!
Follow Ups	3.2L of kick-a$$ > - Ash's Z 22:12:17 06/19/12 Re: 3.2L of kick-a$$ > - LocoZ 22:22:28 06/19/12 Tony's car??? - Jayru 22:35:13 06/19/12 Re: Tony's car??? - 94ttz32 09:02:02 06/20/12 Nope, but the Car took third place by one point over my Z - Zski 18:47:56 06/20/12 freakin' tease :) (n/m) - samsung-Z [Houston] 22:52:37 06/19/12 300 lb-ft at 3250 rpm - Bigwill837 23:32:00 06/19/12 soon (n/m) - ZiNnYc 23:39:21 06/19/12 3.2l ?????????? (n/m) - njz 05:00:40 06/20/12 JUN stroker kit (n/m) - Antihero 08:18:19 06/20/12 three point two liters....it's metric (n/m) - LJZTT 09:12:46 06/20/12 We need a domestic source for a stroker kit... - Bigwill837 13:04:15 06/20/12 Wasn't someone working with Crower to develop one? (n/m) - MixManMash 13:15:10 06/20/12 collegeboy? - Antihero 15:15:45 06/20/12 That's who I was think of. He hasn't been on here in a - MixManMash 15:26:25 06/20/12 I don't know anything about these, but a 3.5 would be sweet! - JMW300ZX 13:43:16 06/20/12 I've dealt with a Paeco build before. - Woody75 (Denver) 14:27:12 06/20/12 ZFromJapan went with them for a MONSTER build - Antihero 15:16:59 06/20/12 I remember him selling off the pieces of that kit - aliaZ 16:03:03 06/20/12 who makes the rods, carrillo? (n/m) - vulcanrush 13:45:07 06/20/12 Jun does. - 90GoldZ 14:03:14 06/20/12 It can be done for around 6k - aliaZ 14:32:39 06/20/12 assuming you wanted a billet crank and light rods... - Antihero 15:21:54 06/20/12 Re: assuming you wanted a billet crank and light rods... - aliaZ 16:02:00 06/20/12 if you cant go wider, would increasing the diameter work? (n/m) - Antihero 16:09:25 06/20/12 then you run into interference with the rod end - aliaZ 17:56:39 06/20/12 end caps and rod bolts should be the main stress points - Red Hawk (CO) 16:24:33 06/20/12 just saying you need more rod bearing surface area. (n/m) - Antihero 16:27:09 06/20/12 not necessarily - aliaZ 17:59:55 06/20/12 Re: It can be done for around 6k - Bigwill837 18:45:49 06/20/12 the stroker has little to do with it IMHO - aliaZ 20:26:42 06/20/12 Re: the stroker has little to do with it IMHO - Bigwill837 20:35:52 06/20/12 Makes you wonder how a standard cookie cutter "built" TT - samsung-Z [Houston] 22:12:34 06/20/12 Re: Makes you wonder how a standard cookie cutter "built" TT - Bigwill837 23:13:41 06/20/12 What lag! (n/m) - NextZ 08:52:16 06/20/12 Amazing powerband! Looking to see more on this car! (n/m) - TheTwinZ (Peru) 09:04:24 06/20/12 Dayyum, mine did 615 rwhp and it was nuts.... - qqqqqqqman 10:56:46 06/20/12 Holy $%&* - RobZ32 11:28:23 06/20/12 he said more info tomorrow........ - sonazty 23:47:31 06/20/12
Post a Followup	You cannot reply to this message because you are not logged in.