Subject	read asap!!!
Posted by	preprodigy on May 20, 2012 at 1:17 AM
	This message has been viewed 121 times.
In Reply To	oil return line...ugh! posted by ouikikazz on May 19, 2012 at 10:40 PM
Message	hey man, if you do decide to re bend those (which isnt a huge deal) 1. mkae sure you remove the oil return stem from the turbo before you do anything, you dont want to put unnecessary tension on those trubos and break mounting bolts ect. 2. befoer you remove, mark return stem were they need to be bent, a line with wat direction to bend in and last a rough measurement of how much to bend. 3. use HEAT! a simple little hand torch and a few minutes circaling the area to be bent will drastaically ease this process. 4. most important of all!, GO SLOW, you dont want to over bend or kink, esp if adding heat! nice and easy =) last thing, when heating. make sure to apply even heat to entire circumference of bend, this will also help to ensure you dont get any kinks. p.s. let us know how it turns out.
Follow Ups	oil return line...ugh! - ouikikazz 22:40:49 05/19/12 Youll have to bend it to make it line up better - Drk93TT 22:48:16 05/19/12 Re: Youll have to bend it to make it line up better - ouikikazz 22:51:12 05/19/12 if you are really worried about kinking it you could fill w/ - FuerGrissa 23:40:24 05/19/12 Re: Youll have to bend it to make it line up better - MR_X 00:37:33 05/20/12 agreed. My sport 700's were low as well. Used a pipe wrench - PiotrC70 00:51:19 05/20/12 Unrelated to your issue but here's another thought for - Xteam300TT (South Tx ) 00:12:21 05/20/12 *Wastegate actuator housings* (n/m) - Xteam300TT (South Tx ) 00:19:14 05/20/12 Clocking the center section should fix that. (n/m) - Evan_Wright (Ca) 00:20:45 05/20/12 Might also throw the water lines off . (n/m) - Xteam300TT (South Tx ) 00:28:35 05/20/12 But then again he did'nt mention if any of the other lines - Xteam300TT (South Tx ) 00:32:47 05/20/12 Re: But then again he did'nt mention if any of the other lines - ouikikazz 01:55:30 05/20/12 the oil return tubes bend pretty easily - aliaZ 06:29:37 05/20/12 2nd (n/m) - MixManMash 07:04:17 05/20/12 Yup, just re-tweaked my stock drain tubes - vorpalZ 23:33:53 05/20/12 Did your turbos come with restricters and are you using - Xteam300TT (South Tx ) 00:26:42 05/20/12 Re: Did your turbos come with restricters and are you using - ouikikazz 01:54:15 05/20/12 read asap!!! - preprodigy 01:17:28 05/20/12 i just cut it and use rubber hose - nissan300zxwork 12:55:34 05/20/12 Thats what I was thinking about doing - ZXoltan 17:05:56 05/20/12 Re: Thats what I was thinking about doing - nissan300zxwork 21:35:17 05/20/12 Anyone tried using regular rubber hose (not silicone) - ZXoltan 04:14:38 05/20/12 Re: Anyone tried using regular rubber hose (not silicone) - preprodigy 05:02:42 05/20/12 Thanks but you totally misunderstood. - ZXoltan 05:56:43 05/20/12 Re: Thanks but you totally misunderstood. - ouikikazz 06:08:02 05/20/12 Z1 sells a similar kit minus the an fitting (n/m) - jlag 09:53:31 05/20/12 U mean the one with the silicone hose? lol (n/m) - ZXoltan 10:14:14 05/20/12 Re: Z1 sells a similar kit minus the an fitting - ouikikazz 10:44:11 05/20/12 The new style have a fluorine liner, not an issue anymore (n/m) - ZiNnYc 13:41:43 05/20/12 RU speaking from experience or Z1's talking points? (n/m) - ZXoltan 17:03:45 05/20/12 I own a set on my Z, and have installed a few. - ZiNnYc 18:26:34 05/20/12 Linsen, How long ago did you buy them? - ZXoltan 18:43:54 05/20/12 I purchased them last year from Coz. - ZiNnYc 19:09:21 05/20/12 btw, if I were to do it again, - ZiNnYc 19:29:16 05/20/12 You need to find a nitrile or oil-resistant rubber to use. (n/m) - boileralum 14:11:10 05/20/12
Post a Followup	You cannot reply to this message because you are not logged in.