Subject	Unrelated to your issue but here's another thought for
Posted by	Xteam300TT (South Tx ) on May 20, 2012 at 12:12 AM
	This message has been viewed 130 times.
In Reply To	oil return line...ugh! posted by ouikikazz on May 19, 2012 at 10:40 PM
Message	you to consider . You may want to rotate your wastegate housings 180* so the nipples face up . This way the hoses come straight up and you dont have to bend the hose to get it on the nipple . I also wouldnt worry about slightly kinking that drain line . It's huge and doesnt see much action especially with the restricted BB Turbos . I would slide a large box end wrench over it and torque on it easily in several places to achieve the correct angle . Good luck
Follow Ups	oil return line...ugh! - ouikikazz 22:40:49 05/19/12 Youll have to bend it to make it line up better - Drk93TT 22:48:16 05/19/12 Re: Youll have to bend it to make it line up better - ouikikazz 22:51:12 05/19/12 if you are really worried about kinking it you could fill w/ - FuerGrissa 23:40:24 05/19/12 Re: Youll have to bend it to make it line up better - MR_X 00:37:33 05/20/12 agreed. My sport 700's were low as well. Used a pipe wrench - PiotrC70 00:51:19 05/20/12 Unrelated to your issue but here's another thought for - Xteam300TT (South Tx ) 00:12:21 05/20/12 *Wastegate actuator housings* (n/m) - Xteam300TT (South Tx ) 00:19:14 05/20/12 Clocking the center section should fix that. (n/m) - Evan_Wright (Ca) 00:20:45 05/20/12 Might also throw the water lines off . (n/m) - Xteam300TT (South Tx ) 00:28:35 05/20/12 But then again he did'nt mention if any of the other lines - Xteam300TT (South Tx ) 00:32:47 05/20/12 Re: But then again he did'nt mention if any of the other lines - ouikikazz 01:55:30 05/20/12 the oil return tubes bend pretty easily - aliaZ 06:29:37 05/20/12 2nd (n/m) - MixManMash 07:04:17 05/20/12 Yup, just re-tweaked my stock drain tubes - vorpalZ 23:33:53 05/20/12 Did your turbos come with restricters and are you using - Xteam300TT (South Tx ) 00:26:42 05/20/12 Re: Did your turbos come with restricters and are you using - ouikikazz 01:54:15 05/20/12 read asap!!! - preprodigy 01:17:28 05/20/12 i just cut it and use rubber hose - nissan300zxwork 12:55:34 05/20/12 Thats what I was thinking about doing - ZXoltan 17:05:56 05/20/12 Re: Thats what I was thinking about doing - nissan300zxwork 21:35:17 05/20/12 Anyone tried using regular rubber hose (not silicone) - ZXoltan 04:14:38 05/20/12 Re: Anyone tried using regular rubber hose (not silicone) - preprodigy 05:02:42 05/20/12 Thanks but you totally misunderstood. - ZXoltan 05:56:43 05/20/12 Re: Thanks but you totally misunderstood. - ouikikazz 06:08:02 05/20/12 Z1 sells a similar kit minus the an fitting (n/m) - jlag 09:53:31 05/20/12 U mean the one with the silicone hose? lol (n/m) - ZXoltan 10:14:14 05/20/12 Re: Z1 sells a similar kit minus the an fitting - ouikikazz 10:44:11 05/20/12 The new style have a fluorine liner, not an issue anymore (n/m) - ZiNnYc 13:41:43 05/20/12 RU speaking from experience or Z1's talking points? (n/m) - ZXoltan 17:03:45 05/20/12 I own a set on my Z, and have installed a few. - ZiNnYc 18:26:34 05/20/12 Linsen, How long ago did you buy them? - ZXoltan 18:43:54 05/20/12 I purchased them last year from Coz. - ZiNnYc 19:09:21 05/20/12 btw, if I were to do it again, - ZiNnYc 19:29:16 05/20/12 You need to find a nitrile or oil-resistant rubber to use. (n/m) - boileralum 14:11:10 05/20/12
Post a Followup	You cannot reply to this message because you are not logged in.